[SOLD OUT] DIY Safe Shutdown v1.0 (for PowerBoost)
-
- Posts: 35
- Joined: Sun Jul 17, 2016 11:37 am
- Has thanked: 16 times
- Been thanked: 4 times
Re: [For Sale] DIY Safe Shutdown v1.0 (for PowerBoost)
Ordered two...
I really hoped that @Camble would release the wiring diagram to build this circuit on my own, but I have to say this is a great deal and with the switch (and of course everything else) not installed, I might be able to place the PCB somewhere else to keep the room.
I really hoped that @Camble would release the wiring diagram to build this circuit on my own, but I have to say this is a great deal and with the switch (and of course everything else) not installed, I might be able to place the PCB somewhere else to keep the room.
Re: [For Sale] DIY Safe Shutdown v1.0 (for PowerBoost)
I might challenge your fool-proof setupCamble wrote:The only thing that may trip people up is getting the transistors mixed up, but everything is marked and only goes in one place.
Just from the photo of the finished product you posted, the colors indicate that there are 5 different resistors for a total of 6.
So from left to right, we have the small red resistor followed by 5 teal ones. Among the teal resistors, do you confirm that teal resistor number 2 and 3 are identical?
Thanks for all your work.
- Camble
- Posts: 885
- Joined: Thu May 05, 2016 2:31 am
- Location: Scotland
- Has thanked: 269 times
- Been thanked: 488 times
Re: [For Sale] DIY Safe Shutdown v1.0 (for PowerBoost)
That's correct. Although, the red one is a diode and must be soldered the correct way round.Eccho wrote:I might challenge your fool-proof setupCamble wrote:The only thing that may trip people up is getting the transistors mixed up, but everything is marked and only goes in one place.
Just from the photo of the finished product you posted, the colors indicate that there are 5 different resistors for a total of 6.
So from left to right, we have the small red resistor followed by 5 teal ones. Among the teal resistors, do you confirm that teal resistor number 2 and 3 are identical?
Thanks for all your work.
Re: [For Sale] DIY Safe Shutdown v1.0 (for PowerBoost)
Ordered two! Thanks! What are the differences from v1.2?
Re: [For Sale] DIY Safe Shutdown v1.0 (for PowerBoost)
Unfortunately sending to my country will be expensive and time consuming (Brazil) Would it be possible for me to pay for the PCB and you send the schematic by e-mail?
That way I mount my PCB and you do not need to send a PCB to me.
Thanks
That way I mount my PCB and you do not need to send a PCB to me.
Thanks
- 144TECH
- Posts: 325
- Joined: Fri Jan 06, 2017 7:30 am
- Location: Amsterdam
- Has thanked: 256 times
- Been thanked: 71 times
Re: [For Sale] DIY Safe Shutdown v1.0 (for PowerBoost)
lol
* Very Rare * GBZ 640x480 v3 Stock Looks 6000MAH
http://www.sudomod.com/forum/viewtopic.php?f=43&t=4863
http://www.sudomod.com/forum/viewtopic.php?f=43&t=4863
- scbailey94
- Posts: 49
- Joined: Wed May 18, 2016 9:57 am
- Has thanked: 11 times
- Been thanked: 7 times
- Contact:
Re: [For Sale] DIY Safe Shutdown v1.0 (for PowerBoost)
@camble Have these been posted out yet? I wasn't sure if you were waiting until you reach a certain amount of orders or something before you send them out
Check out my Instagram www.instagram.com/sb.retromods/ to see more of my Game Boy Zero builds
Who is online
Users browsing this forum: No registered users and 1 guest