Page 1 of 1

[FOR SALE][Worldwide] 3D-Printed DSL GBA Cartridge Slot Mount

Posted: Sat Sep 24, 2016 10:06 pm
by wermy
gba_slot_mount.jpg
gba_slot_mount.jpg (254.41 KiB) Viewed 12297 times
This 3D-Printed part is intended to be used with a modified GBA cartridge slot from a DS-Lite (as shown in part 2 of the all-custom-and-aftermarket-part build guide: sudomod.com/game-boy-zero-custom-parts-guide-part-2 )
It consists of two parts: one that goes below the cartridge slot to help you raise it up just enough, center it, and easily glue it in place, and one part that goes on top to reinforce it.
Screenshot 2016-09-24 18.18.57.jpg
Screenshot 2016-09-24 18.18.57.jpg (549.5 KiB) Viewed 12297 times
Be sure to watch the video guide to more clearly see how to install it!

https://www.youtube.com/watch?v=eM3eNAOCphk

Get it on the market!
http://market.sudomod.com/3d-printed-ds ... slot-mount

STL file for printing your own can be downloaded here: http://sudomod.com/wp-content/uploads/2 ... _mount.zip

Re: [FOR SALE][Worldwide] 3D-Printed DSL GBA Cartridge Slot Mount

Posted: Sun Sep 25, 2016 12:08 am
by AJRedfern
@wermy I'm going to be ordering some of your new 3D printed parts from this part of the project in the next week, if I put in a bit extra could you do a few Volume Wheel and Pi Zero blocks for me also?

Re: [FOR SALE][Worldwide] 3D-Printed DSL GBA Cartridge Slot Mount

Posted: Sun Sep 25, 2016 12:11 am
by damian
What about some of the little 3D printed square pieces? Can I buy a few of those :D

P.S. Just ordered

Re: [FOR SALE][Worldwide] 3D-Printed DSL GBA Cartridge Slot Mount

Posted: Sun Sep 25, 2016 12:25 am
by Ganreizu
@wermy: Can you set up your links to order more than one at a time? :D Thank you <3

Re: [FOR SALE][Worldwide] 3D-Printed DSL GBA Cartridge Slot Mount

Posted: Mon Sep 26, 2016 6:28 am
by WoodMill
Boo. The card reader is the next step of mine, and i JUST drilled holes and mounted my tactile buttons where the back support legs go.

Suppose I could print the brace with added supports moved closer to the center, and then cut off the outside ones. I'll have to print one to see how it looks.

Thanks again for doing all the hard work and releasing it on your site! Love working on this project, but wouldn't have been able to do it without everyone's help and information.

Re: [FOR SALE][Worldwide] 3D-Printed DSL GBA Cartridge Slot Mount

Posted: Thu Feb 02, 2017 3:24 pm
by homebrewchemist
Will this work with the GB Cartridge slot sold on Handheld Legend?

Re: [FOR SALE][Worldwide] 3D-Printed DSL GBA Cartridge Slot Mount

Posted: Fri Feb 03, 2017 6:25 am
by abrugsch
homebrewchemist wrote:Will this work with the GB Cartridge slot sold on Handheld Legend?
(don't know about HHL... if they are DS Lite then yes, if they are DS (fat) then maybe... if they are GBA, unlikely)

It will work with my slots:
http://www.sudomod.com/forum/viewtopic. ... 57&p=21198

Re: [FOR SALE][Worldwide] 3D-Printed DSL GBA Cartridge Slot Mount

Posted: Sun Jun 25, 2017 7:03 pm
by JakeB5
I realize this is a post from long ago, but if I want to order multiples of these how can I do it besides running multiple transactions. Did you aver get a system setup for adding to cart?

Re: [FOR SALE][Worldwide] 3D-Printed DSL GBA Cartridge Slot Mount

Posted: Sun Jun 25, 2017 7:28 pm
by wermy
JakeB5 wrote:
Sun Jun 25, 2017 7:03 pm
I realize this is a post from long ago, but if I want to order multiples of these how can I do it besides running multiple transactions. Did you aver get a system setup for adding to cart?
So no, I never got that set up - orders died down quite a bit so it didn't seem like as much of a necessity. If you have a few things you'd like to get at once, shoot me a PM and we can work it out. :)