HoolyHoo's GBZ with Kite's SAIO

[drafterITA]

https://www.aliexpress.com/item/UXCELL- ... 0832b2f017
https://www.aliexpress.com/item/SK23D07 ... a9e080d4d1
Are These good or it will not work like the SK-22H07?

check ebay too
http://www.ebay.it/itm/20PCS-6mm-High-S ... Swn7JYFDUn

Those do look like the ones I used.

I saw in the description of the item that they are 2 positions switches, and they have 6 pins, so.. I ordered one bag. They are shipped from China, so it might take a while before they arrive.. Oh well, Kite SAIO board is also expected around the end of May, it should be okay

[HoolyHoo]

check ebay too
http://www.ebay.it/itm/20PCS-6mm-High-S ... Swn7JYFDUn

Those do look like the ones I used.

I saw in the description of the item that they are 2 positions switches, and they have 6 pins, so.. I ordered one bag. They are shipped from China, so it might take a while before they arrive.. Oh well, Kite SAIO board is also expected around the end of May, it should be okay

Yes on the 6 pins. You only need two pins for our use. I just snipped off the other legs, since they are not needed.

[drafterITA]

Soo.. my dad destroyed his phone, so I ravaged it for parts (Samsung Galaxy S4, the battery is unfortunately too big..) and I could cut the battery connector in 1 piece. But I have no clue if it could fit the battery you used @HoolyHoo, could you, when you have time, tell me the measurements of the connections on the battery? What's the distance between each one of them etc etc..
Thank you very much

[HoolyHoo]

Soo.. my dad destroyed his phone, so I ravaged it for parts (Samsung Galaxy S4, the battery is unfortunately too big..) and I could cut the battery connector in 1 piece. But I have no clue if it could fit the battery you used @HoolyHoo, could you, when you have time, tell me the measurements of the connections on the battery? What's the distance between each one of them etc etc..
Thank you very much

Yeah you need that s2 battery. Height wise and width is perfect. Length needs a very slight modifican to the case. Only need to trim about 1mm from one of the sides for a tight fit or both sides if you want it loose in the case. There is a lip on both sides that makes that possible. You won't even notice it's altered. The plastic there is about 2mm thick so you don't need to completely cut that wall out.

I measured the distance between each of the four tabs and it's hard to get a perfect reading but it's pretty close to 2.5mm from center to center of each tab. I believe the first and third pins are the two you need.

[drafterITA]

Yeah you need that s2 battery. Height wise and width is perfect. Length needs a very slight modifican to the case. Only need to trim about 1mm from one of the sides for a tight fit or both sides if you want it loose in the case. There is a lip on both sides that makes that possible. You won't even notice it's altered. The plastic there is about 2mm thick so you don't need to completely cut that wall out.

I measured the distance between each of the four tabs and it's hard to get a perfect reading but it's pretty close to 2.5mm from center to center of each tab. I believe the first and third pins are the two you need.

Thank you very much
I'll measure that connector I have and post some pictures if it fits!

[diegoquimico]

Which cell pone did you use to extrac pogo pìns? Thanks!! (Pics?)

[HoolyHoo]

Which cell pone did you use to extrac pogo pìns? Thanks!! (Pics?)

Here is the actual connector that goes with that battery.

http://www.witrigs.com/replacement-part ... 2-gt-i9100

[abrugsch]

Soo.. my dad destroyed his phone, so I ravaged it for parts (Samsung Galaxy S4, the battery is unfortunately too big..) and I could cut the battery connector in 1 piece. But I have no clue if it could fit the battery you used @HoolyHoo, could you, when you have time, tell me the measurements of the connections on the battery? What's the distance between each one of them etc etc..
Thank you very much

The S4 might just use the same battery terminal pitch. The S3 certainly does.
Anyway here's the S2 battery:

IMG_20170406_131508.jpg (2.75 MiB) Viewed 24850 times

[drafterITA]

Soo.. my dad destroyed his phone, so I ravaged it for parts (Samsung Galaxy S4, the battery is unfortunately too big..) and I could cut the battery connector in 1 piece. But I have no clue if it could fit the battery you used @HoolyHoo, could you, when you have time, tell me the measurements of the connections on the battery? What's the distance between each one of them etc etc..
Thank you very much

The S4 might just use the same battery terminal pitch. The S3 certainly does.
Anyway here's the S2 battery:
IMG_20170406_131508.jpg

If those in your picture are cm, then my connector should be perfect

IMG_20170406_152155_01.jpg (238.87 KiB) Viewed 24830 times

Thank you abrugsch and HollyHoo

[HoolyHoo]

Soo.. my dad destroyed his phone, so I ravaged it for parts (Samsung Galaxy S4, the battery is unfortunately too big..) and I could cut the battery connector in 1 piece. But I have no clue if it could fit the battery you used @HoolyHoo, could you, when you have time, tell me the measurements of the connections on the battery? What's the distance between each one of them etc etc..
Thank you very much

The S4 might just use the same battery terminal pitch. The S3 certainly does.
Anyway here's the S2 battery:
IMG_20170406_131508.jpg

If those in your picture are cm, then my connector should be perfect
IMG_20170406_152155_01.jpg

Thank you abrugsch and HollyHoo

Looks like an exact match to me.