Search found 55 matches

by J-Malice
Mon Oct 16, 2017 9:50 am
Forum: Resolved Issues (mintyPi)
Topic: [Solved] Microlipo LEDs staying on
Replies: 22
Views: 8964

Re: Microlipo LEDs staying on

Image



Image



Image



Image
by J-Malice
Mon Oct 16, 2017 9:38 am
Forum: Resolved Issues (mintyPi)
Topic: [Solved] Microlipo LEDs staying on
Replies: 22
Views: 8964

Re: Microlipo LEDs staying on

Additional information, I had a closing issue (made a thread about it on this forum) as well as no audio. I figured pop it open and check the USB audio card and then check the 3d printed hinge. Sure enough the + power wire on the usb audio card was nearly torn off on the USB card end. No big deal, r...
by J-Malice
Mon Oct 16, 2017 9:08 am
Forum: Support (mintyPi)
Topic: [Not Solved]Closing the tin "sticks"
Replies: 5
Views: 1488

Re: Closing the tin "sticks"

Found the issue. The edge of the tin was slightly bent (don't know when that happened?) near the 3d printed hinge. It was causing the 3d printed hinge to get stuck under the bent part when it closed fully and putting strain on the pi during opening and closing. Thanks for the reply though! Wrong wr...
by J-Malice
Mon Oct 16, 2017 9:02 am
Forum: Resolved Issues (mintyPi)
Topic: [Solved] Microlipo LEDs staying on
Replies: 22
Views: 8964

[Solved] Microlipo LEDs staying on

Been troubleshooting some power issues and had the pcb up so I could examine cabling. I figured I'd plug it in to charge since maybe the battery was just dead or something. It started charging and didnt seem to have an issue. Looked down and both LED's were on so I unplugged it. But both stayed on a...
by J-Malice
Sun Oct 15, 2017 6:24 pm
Forum: Support (mintyPi)
Topic: [Not Solved]Closing the tin "sticks"
Replies: 5
Views: 1488

[Not Solved]Closing the tin "sticks"

I didn't know where to post this but it seemed appropriate here. I have my minty pi assembled but I have a problem opening it. When I close it there is no issue really. When I try to open it the left side sticks a bit and is extremely hard to open. So hard that I've actually bent the hinge a little....
by J-Malice
Sun Oct 15, 2017 9:02 am
Forum: Show-off Corner (mintyPi)
Topic: Fresh pi
Replies: 3
Views: 1623

Fresh pi

Image

The outside isn't bad. Pretty basic.



Image

The inside has a nice little flourish. Enamel paint to make the symbol pop. Silver leaf and Cobalt raspberry.
by J-Malice
Thu Oct 12, 2017 12:02 pm
Forum: For Sale/Trade
Topic: [For Sale, Preorder] DMG pre-cut cases
Replies: 433
Views: 115429

Re: [For Sale, Preorder] DMG pre-cut cases

Arrived here. Thanks man, looks good.
by J-Malice
Wed Oct 11, 2017 1:43 pm
Forum: Support (mintyPi)
Topic: White screen
Replies: 77
Views: 18839

Re: White screen

DC looks like it doesn't have enough solder. Did you see my last post on the previous page? Check the 4 gpio that I mentioned. My screen was exactly like that until I made sure to press the soldering iron deep into each opening and apply a *very* little bit more solder to each. Edit: also, you have ...
by J-Malice
Tue Oct 10, 2017 11:32 am
Forum: Support (mintyPi)
Topic: White screen
Replies: 77
Views: 18839

Re: White screen

Can you get a closer picture of the gpio pins?
by J-Malice
Mon Oct 09, 2017 6:27 pm
Forum: Support (mintyPi)
Topic: White screen
Replies: 77
Views: 18839

Re: White screen

How did you check the gpio?