Search found 116 matches
- Mon Mar 05, 2018 6:46 pm
- Forum: Design Sharing (3d Printing)
- Topic: [UPDATE] "Air duct" and "fan-mount" for kites circuit sword
- Replies: 46
- Views: 45951
Re: [WIP] Fan/blower mount for kites circuit sword
Kinda wondering if there is ETA on the release of the files for the new brackets?
- Sun Mar 04, 2018 9:14 pm
- Forum: Design Sharing (3d Printing)
- Topic: [FINISHED] Tact-4 shoulder button bracket for GBZ
- Replies: 70
- Views: 59241
Re: [WIP] Tact-4 shoulder button bracket
Could you fit a DMG button with this kind of fit / configuration? Due to to size of the buttons and the mechanics it may run into some space problems with other components. I have seen simular designs where a bigger tact button would be pretty close to other components, but it would be really diffi...
- Sun Mar 04, 2018 2:40 pm
- Forum: Design Sharing (3d Printing)
- Topic: [FINISHED] Tact-4 shoulder button bracket for GBZ
- Replies: 70
- Views: 59241
Re: [WIP] Tact-4 shoulder button bracket
So here is what came out next.
On the left, the drill guide. Right, final mount. Right now Its only theory, so don't drill anything.
current files
https://www.dropbox.com/s/aefnx8gn8cipt ... 0.zip?dl=0
On the left, the drill guide. Right, final mount. Right now Its only theory, so don't drill anything.
current files
https://www.dropbox.com/s/aefnx8gn8cipt ... 0.zip?dl=0
- Sat Mar 03, 2018 3:16 pm
- Forum: Design Sharing (3d Printing)
- Topic: [FINISHED] Tact-4 shoulder button bracket for GBZ
- Replies: 70
- Views: 59241
Re: [WIP] Tact-4 shoulder button bracket
So did some test prints and I am I a few more things to do. Since I do have a clear case It makes it easier to see where the buttons would end up. So far it looks like having them go straight down and bit space out is the way to go. https://i.imgur.com/8pjDmx0.jpg However the way it sits now even my...
- Thu Mar 01, 2018 8:44 pm
- Forum: Design Sharing (3d Printing)
- Topic: [FINISHED] Tact-4 shoulder button bracket for GBZ
- Replies: 70
- Views: 59241
Re: [WIP] Tact-4 shoulder button bracket
Now that I got the fit to the gameboy correct. Now I need to get to the fit to the tact switches going. From one my earlier versions it wasn't an issue. Luckly I still have the place holders to work from. https://i.imgur.com/pykhpvr.png https://i.imgur.com/cRn5N6Q.png https://i.imgur.com/vBnWyfw.png...
- Wed Feb 28, 2018 11:42 am
- Forum: Design Sharing (3d Printing)
- Topic: [UPDATE] "Air duct" and "fan-mount" for kites circuit sword
- Replies: 46
- Views: 45951
Re: [WIP] Fan/blower mount for kites circuit sword
Not thrilled about re soldering the fan. All these brackets look incredible.
Honestly I didn't notice any interference between the parts.
Honestly I didn't notice any interference between the parts.
- Tue Feb 27, 2018 9:16 pm
- Forum: Support for Kite's Products
- Topic: CSO adding lights
- Replies: 2
- Views: 3057
CSO adding lights
I know I asked this before on the big pre-order thread and I cannot remember the answer or find it. So I have to ask it again. I am considering adding some leds to my GBZ since its in a clear case. I know that it was recommended that I solder it into a test pad so that I can turn it on or off with a...
- Sun Feb 25, 2018 8:30 am
- Forum: Design Sharing (3d Printing)
- Topic: [FINISHED] Tact-4 shoulder button bracket for GBZ
- Replies: 70
- Views: 59241
Re: [WIP] Tact-4 shoulder button bracket
Made adjustments with hoolyhoos switch bracket. Essentially the way I approached it was to import the part into blender, and make the one section of it bigger, and extend it down so that I could have the wiggle room. NEW LINK https://www.dropbox.com/s/c09xo2y1cgdzxcg/sholderbutton%20bracket-v8blank....
- Sat Feb 24, 2018 5:57 pm
- Forum: Show-off Corner (3d Printing)
- Topic: I'm excited...the wife, not so much.
- Replies: 7
- Views: 11955
Re: I'm excited...the wife, not so much.
Print your wife a swan, wives loves swans https://www.thingiverse.com/thing:731686
- Sat Feb 24, 2018 5:01 pm
- Forum: Design Sharing (3d Printing)
- Topic: Glue Less Support Bracket for Kite's Mode/Power Switch Board
- Replies: 58
- Views: 104135
Re: Glue Less Support Bracket for Kite's Mode/Power Switch Board
Hoolyhoo, Looks like its nothing major. Gray part is mine and they are close, i can make some adjustments.