Search found 279 matches
- Mon Feb 19, 2018 5:19 pm
- Forum: General Project Chat
- Topic: Look, I'm clueless.
- Replies: 4
- Views: 3624
- Fri Feb 16, 2018 9:05 am
- Forum: Support for Kite's Products
- Topic: [DISCUSS] Compute Board 3 versus Lite board
- Replies: 3
- Views: 3393
Re: Compute Board 3 versus Lite board
According to Adafruit, the lite version also lacks wi-fi/bluetooth. Is that not correct?
https://www.adafruit.com/product/3441
https://www.adafruit.com/product/3441
- Thu Feb 15, 2018 8:02 am
- Forum: Support (3d Printing)
- Topic: Is this under extruding or possible bad filament
- Replies: 18
- Views: 21138
Re: Is this under extruding or possible bad filament
Inland is a popular, reputable, quality brand. It's not the filament. Something is wrong with your setup - either mechanically or in your slicer settings. You need to start troubleshooting from the ground up. Three places I'd start: is your filament feeding correctly (is the spool sticking/catching?...
- Tue Feb 13, 2018 7:36 pm
- Forum: Support (3d Printing)
- Topic: Is this under extruding or possible bad filament
- Replies: 18
- Views: 21138
Re: Is this under extruding or possible bad filament
How thick is your first layer - both actual thickness and layer setting in your slicer?
- Tue Feb 13, 2018 1:11 pm
- Forum: Looking to Buy
- Topic: [WANTED] Mintypi 2.0
- Replies: 2
- Views: 2148
- Tue Feb 13, 2018 10:39 am
- Forum: Lounge
- Topic: Wow, 3DHubs *REALLY* sucks, now.
- Replies: 3
- Views: 4703
Re: Wow, 3DHubs *REALLY* sucks, now.
They're gradually rolling it out across the globe. They implemented the change in the US in October(?) last year, and just rolled it out in Canada and Australia a week ago. Presumably they'll start in Europe next. There was a huge uproar among US hubs when they rolled it out there last year. They sh...
- Tue Feb 13, 2018 10:10 am
- Forum: Support (3d Printing)
- Topic: Is this under extruding or possible bad filament
- Replies: 18
- Views: 21138
Re: Is this under extruding or possible bad filament
extruder at 215 f bed at 70 speed at 50mm/s I'm guessing you mean 215 C; 215 F would be way too low. :) I'd say your bed temperature is too high for PLA, too, but that's not going to cause this problem. Speed is fine, too, assuming you're satisfied with the print quality. Few thoughts... It's proba...
- Mon Feb 12, 2018 11:08 am
- Forum: General Chat (mintyPi)
- Topic: mintyPi preorder interest poll
- Replies: 44
- Views: 30100
Re: mintyPi preorder interest poll
No, not 'first'.
The answer to your question could have been found in the post directly above your question.
The answer to your question could have been found in the post directly above your question.
- Sun Feb 11, 2018 2:57 pm
- Forum: Support for Kite's Products
- Topic: [SOLVED] CSO - How to add a Nintendo DS Joystick
- Replies: 6
- Views: 6912
Re: Nintendo DS Joystick
No, the black plastic is on the white tab you snapped off. You should be able to desolder the ribbon cable, then you can solder your wires to the bare PCB. Just heat your iron up, place it across the pads (you may need to work the iron back and forth to heat them all) and gently pull up on the ribbo...
- Sun Feb 11, 2018 2:49 pm
- Forum: General Chat (mintyPi)
- Topic: mintyPi preorder interest poll
- Replies: 44
- Views: 30100