Nevermind, the 1000 basic and 1000C use different step-up chips, and the 1000C can't deliver as much current. Need to go with the 1000basic and a separate charging board!Fredl wrote: ↑Sat Mar 03, 2018 6:06 amHi, I'm doing this build as well and was wondering: Banjo used the Powerboost 1000 basic, which can deliver 2A at 3.7V. Would it be possible to use the Powerboost 1000C as well? The data sheet isn't really clear on the actual amps it will deliver, it just says 1000mA+...
Banjo stated the whole system draws 1.7A, so thats a big "+"...
Or alternatively, what kind of battery charging circuit can I use in combination with the 1000basic?
(All the ones I find are charger & DC-DC-step-up combined but limited to 1A...)
Thanks!
WII U RASPBERRY PI 3 FINISHED
Re: WII U RASPBERRY PI 3 FINISHED
I used to be an adventurer like you, but then I took an arrow in the knee :-O
Link: Downmix your GBZs sound to mono or you're missing half the fidelity!
Link: Downmix your GBZs sound to mono or you're missing half the fidelity!
Re: WII U RASPBERRY PI 3 FINISHED
Hello all. Hello @banjokazooie.
I just made a new diagram. Cleaner, I think.
But I'm encountering a riddle...
I followed this guide to find out how to wiring : https://www.sudomod.com/forum/viewtopic ... 956#p23956 and the author of the WiiU PCB disappeared too
I'm clearly lost. And i don't know where to wire the : Home Led 1, Home Led 2 and Batt Led.
And i don't know if my diagram is good
Big help and very big thanks
I just made a new diagram. Cleaner, I think.
But I'm encountering a riddle...
I followed this guide to find out how to wiring : https://www.sudomod.com/forum/viewtopic ... 956#p23956 and the author of the WiiU PCB disappeared too
I'm clearly lost. And i don't know where to wire the : Home Led 1, Home Led 2 and Batt Led.
And i don't know if my diagram is good
Big help and very big thanks
- banjokazooie
- Posts: 211
- Joined: Thu May 19, 2016 1:14 pm
- Location: https://t.me/pump_upp
- Been thanked: 171 times
- Contact:
Re: WII U RASPBERRY PI 3 FINISHED
The battery led in original design was wired from powerboost basic, with 7.2V setup you need to wire a basic resistor divider. Read analog voltage from this divider with analog input on teensy and setup a digital output to led. Home leds as wired to digital output on teensy and a reguired event is set up inside teensy code.Marty33 wrote: ↑Sun Mar 04, 2018 1:57 pmHello all. Hello @banjokazooie.
I just made a new diagram. Cleaner, I think.
But I'm encountering a riddle...
I followed this guide to find out how to wiring : https://www.sudomod.com/forum/viewtopic ... 956#p23956 and the author of the WiiU PCB disappeared too
I'm clearly lost. And i don't know where to wire the : Home Led 1, Home Led 2 and Batt Led.
And i don't know if my diagram is good
Big help and very big thanks
Re: WII U RASPBERRY PI 3 FINISHED
Ok. Big thanks for this tips.
For the battery, i search good capacity "mAh". But i see different "A". It's important ? 10A, 15A, 20A ?
Max. charge current, Charge voltage, End voltage, continuous max discharge current...
Do I have to respect specific parameters?
For the battery, i search good capacity "mAh". But i see different "A". It's important ? 10A, 15A, 20A ?
Max. charge current, Charge voltage, End voltage, continuous max discharge current...
Do I have to respect specific parameters?
Re: WII U RASPBERRY PI 3 FINISHED
Thanks a lot for showing this awesome project and provide all the informations!
But I have two questions:
1. Is it possible to just remove the battery / recharging setup and use the micro usb as power supply for the pi?
2. Can I remove the TEENSY and use 2 arcade USB encoder like this one: https://www.amazon.de/Quimat-Nullverz%C ... =srch&th=1
I don't know if the buttons and controller sticks work similar to an arcade setup so I just can rewire them.
Thanks a lot and I hope, that my questions are not to noobie
But I have two questions:
1. Is it possible to just remove the battery / recharging setup and use the micro usb as power supply for the pi?
2. Can I remove the TEENSY and use 2 arcade USB encoder like this one: https://www.amazon.de/Quimat-Nullverz%C ... =srch&th=1
I don't know if the buttons and controller sticks work similar to an arcade setup so I just can rewire them.
Thanks a lot and I hope, that my questions are not to noobie
- banjokazooie
- Posts: 211
- Joined: Thu May 19, 2016 1:14 pm
- Location: https://t.me/pump_upp
- Been thanked: 171 times
- Contact:
Re: WII U RASPBERRY PI 3 FINISHED
Any Lipo for raspberry is good enough as you will not be drawing that much current. Don't go too crazy on capacity as the charging will take forever. So i would say 6000-8000mAh is a good choice .Marty33 wrote: ↑Tue Mar 06, 2018 4:16 pmOk. Big thanks for this tips.
For the battery, i search good capacity "mAh". But i see different "A". It's important ? 10A, 15A, 20A ?
Max. charge current, Charge voltage, End voltage, continuous max discharge current...
Do I have to respect specific parameters?
- banjokazooie
- Posts: 211
- Joined: Thu May 19, 2016 1:14 pm
- Location: https://t.me/pump_upp
- Been thanked: 171 times
- Contact:
Re: WII U RASPBERRY PI 3 FINISHED
Yes you can use that for powering the raspberry.Apock212 wrote: ↑Thu Mar 08, 2018 6:57 amThanks a lot for showing this awesome project and provide all the informations!
But I have two questions:
1. Is it possible to just remove the battery / recharging setup and use the micro usb as power supply for the pi?
2. Can I remove the TEENSY and use 2 arcade USB encoder like this one: https://www.amazon.de/Quimat-Nullverz%C ... =srch&th=1
I don't know if the buttons and controller sticks work similar to an arcade setup so I just can rewire them.
Thanks a lot and I hope, that my questions are not to noobie
You can remove the Teensy but you will loose analog joysticks as the arcade board are only digital.
Re: WII U RASPBERRY PI 3 FINISHED
@banjokazooie
How comes the screen ribbon cable comes out on top of your build?
Did you mount the screen upside down or do we have different models?
How comes the screen ribbon cable comes out on top of your build?
Did you mount the screen upside down or do we have different models?
I used to be an adventurer like you, but then I took an arrow in the knee :-O
Link: Downmix your GBZs sound to mono or you're missing half the fidelity!
Link: Downmix your GBZs sound to mono or you're missing half the fidelity!
- banjokazooie
- Posts: 211
- Joined: Thu May 19, 2016 1:14 pm
- Location: https://t.me/pump_upp
- Been thanked: 171 times
- Contact:
Re: WII U RASPBERRY PI 3 FINISHED
Mine is 6.5 inch AT065TN14 800*480. It is upside down as the bottom edge of the front cover is thinner.
Re: WII U RASPBERRY PI 3 FINISHED
True, it fits much nicer this way. One moe question though:banjokazooie wrote: ↑Sun Mar 11, 2018 2:28 pmMine is 6.5 inch AT065TN14 800*480. It is upside down as the bottom edge of the front cover is thinner.
How did you rotate the screen? putting
Code: Select all
display_hdmi_rotate=2
Code: Select all
vcgencmd display_hdmi_rotate
Code: Select all
display_hdmi_rotate is unknown
I used to be an adventurer like you, but then I took an arrow in the knee :-O
Link: Downmix your GBZs sound to mono or you're missing half the fidelity!
Link: Downmix your GBZs sound to mono or you're missing half the fidelity!
Who is online
Users browsing this forum: No registered users and 1 guest