I'll give it a crack when I get some time, really shouldn't be too hard.dominator wrote:I would design this, but at the moment I an working on the screen surround and also I would have to find a someone to print them out.wermy wrote:Hey that's a good idea.dominator wrote:That reminds me, I was going to ask if someone could print the button wells
I like the idea of printed button wells, it would be a simple drill and stick button modification! The buttons and conductive pads are easy to find.
3D Printing Forum
- wermy
- Site Admin
- Posts: 1346
- Joined: Tue May 03, 2016 8:51 pm
- Has thanked: 620 times
- Been thanked: 1322 times
- Contact:
Re: 3D Printing Forum
- wermy
- Site Admin
- Posts: 1346
- Joined: Tue May 03, 2016 8:51 pm
- Has thanked: 620 times
- Been thanked: 1322 times
- Contact:
Re: 3D Printing Forum
My calipers say:SP33 wrote:@Wermy Do you know of the button well measurements or where I can get them? I might need to make some for my project as well.
Outside is about 13.75mm
Walls are just a hair under 2mm thick
Walls look to be about 4mm tall (hard to measure that one)
The teeth on the buttons are right at 2mm
Buttons themselves are just a hair over 10mm
- Fleder
- Posts: 849
- Joined: Thu May 05, 2016 9:04 am
- Location: Germany
- Has thanked: 183 times
- Been thanked: 258 times
Re: 3D Printing Forum
Cut a piece of paper, hold it to the side of the button well, mark the height with a pencil and measure this piece of paperwermy wrote:Walls look to be about 4mm tall (hard to measure that one)
-
- Posts: 17
- Joined: Mon Jun 06, 2016 4:27 am
- Location: Zürich, Switzerland
- Has thanked: 7 times
- Been thanked: 1 time
Re: 3D Printing Forum
This is great. I originally found out about the GBZ and became interested in it. In the meantime I decided to go a different approach due to difficulties obtaining a DMG-01 case and create a SuperGameGirl instead.
I'm completing this with a friend and we're pretty much done, just needs some finishing touches on the 3D printed cases! :p
I'm completing this with a friend and we're pretty much done, just needs some finishing touches on the 3D printed cases! :p
-
- Posts: 10
- Joined: Fri May 06, 2016 5:11 pm
- Has thanked: 1 time
- Been thanked: 2 times
Re: 3D Printing Forum
If you guys are looking for a nice bezel for the screen after its mounted, head over to my thread in the Sudomod Projects show-off corner. There is a link to the .stl file. Pictures of it are there too! PM me with any questions! I went through www.3dhubs.com to get mine printed. Only cost $10 total including shipping. I made it in Autodesk 123D. If youd like to check it out or change any dimensions I can send you the project file so you don't have to start from scratch. Super easy free software. Let me know!
-
- Posts: 39
- Joined: Thu May 05, 2016 8:54 am
- Has thanked: 1 time
- Been thanked: 1 time
Re: 3D Printing Forum
My girlfriend and I are slowly building a 3d printer at the moment. Looking foward to printing some bits for this project.
Re: 3D Printing Forum
Nice that sounds like a good investment of your time if you like DIY stuff like this. Mind sharing your resource for this?RasputiNZ wrote:My girlfriend and I are slowly building a 3d printer at the moment. Looking foward to printing some bits for this project.
Who is online
Users browsing this forum: No registered users and 1 guest