Page 9 of 13

Re: How To - Build the PRS-Tech SNES-Zero

Posted: Thu Aug 24, 2017 12:50 pm
by Nemo1984
Once the PP20 HDMI is soldered to P2 of the GPIO, what would happen if I also plug a usb power supply? With a regular HDMI cable, no voltage inserter? Is there a risk of frying the HDMI at the TV, since way more than 50ma is going to get right into it?

EDIT: I think I just answered myself: the diode. That's why there is a diode and not a simple jumper. So after the pins are soldered, the voltage inserter will always be needed.

Re: How To - Build the PRS-Tech SNES-Zero

Posted: Tue Sep 05, 2017 10:24 am
by Raquor
I've recently built this and for the most part it's working great. However when I managed to connect a bluetooth keyboard to the pi 0 w using this setup it became unstable and would reboot every 1-3 minutes until the sd card eventually became unstable and I had to start from scratch.

Does anyone have any tips for avoiding or diagnosing what might have caused the issue? I thought maybe the power source was too low so I tried using an old iPad plug which output 2.4A but that didn't change anything. Could a bad solder joint be causing the issue?

Re: How To - Build the PRS-Tech SNES-Zero

Posted: Wed Sep 06, 2017 2:15 am
by Rabauz
I have two questions:
1. Does anyone from europe (ideally germany) have an alternative list of suppliers for the parts?
and 2. a question @prerunnerseth :how long does the delivery to germany approximately take?
I'm planing on giving it a away as a gift and of course I'm way behind schedule. :)

Re: How To - Build the PRS-Tech SNES-Zero

Posted: Sat Sep 16, 2017 11:21 pm
by RhinoNigel
will this power hdmi adaptor work? It's a fraction of the cost and has no specs so that has me concerned. https://www.ebay.com/itm/371824763217

Re: How To - Build the PRS-Tech SNES-Zero

Posted: Fri Sep 22, 2017 12:36 pm
by Sibbie
The PRS-Tech SNES-Zero works great through the HDMI on a TV; but I would also like to connect it to a VGA computer monitor from time to time. I tried the Tendak HDMI to VGA adaptor (link below) but no picture or audio would go through.

https://www.amazon.com/gp/product/B01B7 ... UTF8&psc=1

Has anyone else found an adaptor to use the PRS-Tech SNES-Zero through the VGA port on a computer monitor?

Re: How To - Build the PRS-Tech SNES-Zero

Posted: Fri Sep 22, 2017 8:32 pm
by Racerboy
Sibbie wrote:
Fri Sep 22, 2017 12:36 pm
The PRS-Tech SNES-Zero works great through the HDMI on a TV; but I would also like to connect it to a VGA computer monitor from time to time. I tried the Tendak HDMI to VGA adaptor (link below) but no picture or audio would go through.

https://www.amazon.com/gp/product/B01B7 ... UTF8&psc=1

Has anyone else found an adaptor to use the PRS-Tech SNES-Zero through the VGA port on a computer monitor?
Is it possible that VGA adapter is not supplying enough power to the pi through HDMI?

Re: How To - Build the PRS-Tech SNES-Zero

Posted: Sat Sep 23, 2017 5:32 am
by Sibbie
Racerboy wrote:
Fri Sep 22, 2017 8:32 pm
Sibbie wrote:
Fri Sep 22, 2017 12:36 pm
The PRS-Tech SNES-Zero works great through the HDMI on a TV; but I would also like to connect it to a VGA computer monitor from time to time. I tried the Tendak HDMI to VGA adaptor (link below) but no picture or audio would go through.

https://www.amazon.com/gp/product/B01B7 ... UTF8&psc=1

Has anyone else found an adaptor to use the PRS-Tech SNES-Zero through the VGA port on a computer monitor?
Is it possible that VGA adapter is not supplying enough power to the pi through HDMI?
I am still using the HDMI with USB Power adapter; so the Pi is still receiving power. The VGA adapter just won't transmit the data from the HDMI/USB adapter to the monitor. Maybe I had a bad adapter.

Re: How To - Build the PRS-Tech SNES-Zero

Posted: Sun Sep 24, 2017 4:55 pm
by RhinoNigel
Just wanted to throw this out there, I didn't want to pay 20$ for the hdmi USB power adapter and got a 5$ one. It works fine.

https://www.ebay.com/itm/182741332011

Re: How To - Build the PRS-Tech SNES-Zero

Posted: Mon Sep 25, 2017 12:54 am
by Rabauz
RhinoNigel wrote:
Sun Sep 24, 2017 4:55 pm
Just wanted to throw this out there, I didn't want to pay 20$ for the hdmi USB power adapter and got a 5$ one. It works fine.

https://www.ebay.com/itm/182741332011
Were you able to pry it open?

Re: How To - Build the PRS-Tech SNES-Zero

Posted: Tue Sep 26, 2017 9:29 pm
by RhinoNigel
Rabauz wrote:
Mon Sep 25, 2017 12:54 am
RhinoNigel wrote:
Sun Sep 24, 2017 4:55 pm
Just wanted to throw this out there, I didn't want to pay 20$ for the hdmi USB power adapter and got a 5$ one. It works fine.

https://www.ebay.com/itm/182741332011
Were you able to pry it open?

I used a xacto knife and cut the one side so it came apart. It has a plastic casing inside which I removed part of. I then put the rubber piece i cut in half back over it and put a piece of electrical tape over it.