Page 3 of 12

Re: OSD Battery Monitoring for Helder's AIO Boards

Posted: Sun May 14, 2017 7:12 am
by HoolyHoo
umbynos95 wrote:
Sun May 14, 2017 7:06 am
Hello, I don't have a USBasp Programmer, it is possible to use this guide instead? (http://www.sudomod.com/forum/viewtopic.php?f=25&t=1176).
I haven't used that method but as long as you get it to write the hex then yes.

Re: OSD Battery Monitoring for Helder's AIO Boards

Posted: Thu May 18, 2017 8:03 am
by Lphillimore
Hi @hoolyhoo - So my 6pin adapter arrived and i proceeded to flash the board with your nex Hex.

This was successful so booted the GBZ but no gamepad detected.

Tried a couple more times, still no joy.

Im using one of @Helder AIO 2.2

To make sure i was flashing the hex OK i test flashed Helders new Hex code and Gamepad was detected fine.

Any ideas?

Ive tried all 3 of your Hex' just to be sure. No gamepad detected for any? :ugeek:

Cheers

Re: OSD Battery Monitoring for Helder's AIO Boards

Posted: Thu May 18, 2017 8:11 am
by HoolyHoo
Lphillimore wrote:
Thu May 18, 2017 8:03 am
Hi @hoolyhoo - So my 6pin adapter arrived and i proceeded to flash the board with your nex Hex.

This was successful so booted the GBZ but no gamepad detected.

Tried a couple more times, still no joy.

Im using one of @Helder AIO 2.2

To make sure i was flashing the hex OK i test flashed Helders new Hex code and Gamepad was detected fine.

Any ideas?

Ive tried all 3 of your Hex' just to be sure. No gamepad detected for any? :ugeek:

Cheers
Hmmm. Not sure. Can you walk me through your steps and maybe screen shots of avrdude after complete? I know other users have used it fine. Let me know.

Re: OSD Battery Monitoring for Helder's AIO Boards

Posted: Thu May 18, 2017 8:16 am
by Lphillimore
Thanks for quick reply.

Sure:

Upon connecting it detects AIO:

'Detected 1e9587 = ATmega32U4'


I then programme and all seems OK. As above, i tried Helders Hex and it detects so not sure its the programming? Odd though as others have had success and im using an AIO2.2

Here are screenshots of the programming start to finish:

Setup:
1.JPG
1.JPG (79.21 KiB) Viewed 13033 times
Writing:
2.JPG
2.JPG (105.59 KiB) Viewed 13033 times
Complete:
3.JPG
3.JPG (95.69 KiB) Viewed 13033 times

Re: OSD Battery Monitoring for Helder's AIO Boards

Posted: Thu May 18, 2017 8:24 am
by HoolyHoo
It looks fine. I uploaded a file called TestAnalog.hex to my github. Can you test that please?

Re: OSD Battery Monitoring for Helder's AIO Boards

Posted: Thu May 18, 2017 8:33 am
by Lphillimore
Thanks! Really appreciate your help.

Just tested that Test hex but still no joy. Not detected :?:

FYI i have no analog.

Re: OSD Battery Monitoring for Helder's AIO Boards

Posted: Thu May 18, 2017 8:35 am
by Lphillimore
I havent yet wired up the additional wires to AIO and Powerboost BTW, not sure of the code relies on that being in place?

Re: OSD Battery Monitoring for Helder's AIO Boards

Posted: Thu May 18, 2017 8:41 am
by HoolyHoo
Check your PM.

Re: OSD Battery Monitoring for Helder's AIO Boards

Posted: Thu May 18, 2017 9:01 am
by HoolyHoo
This is with a leonardo on my computer since I don't have a Helder board available right now but its the same thing.
Screen Shot 2017-05-18 at 10.59.44 AM.png
Screen Shot 2017-05-18 at 10.59.44 AM.png (372.28 KiB) Viewed 13016 times

Re: OSD Battery Monitoring for Helder's AIO Boards

Posted: Thu May 18, 2017 2:55 pm
by Lphillimore
Thanks for your help - all sorted and Gamepad now detected. Extracting the Hex from the entire 'gbzbatterymonitor-master' worked a treat.

Downloading the single Hex' from Github results in larger files which didn't work.

Now for the battery monitor code and test!