sudomod

144TECH wrote: ↑

Sun Aug 20, 2017 12:27 pm

@ HoolyHoo,

I did install everything manually, that worked & everything got installed.
However, i guess i made a little mistake at the last rule wich has to be applied in rc.local , i could have entered that line incorrect.
But, i can do this one to get it right ( sudo sed -i '/\"exit 0\"/!s/exit 0/\/home\/pi\/gbzbatterymonitor\/HHMonitorStart.sh \&\nexit 0/g' /etc/rc.local ) so in this way it can't be wrong.
Now the only questions that last are, if that rule is typed or placed wrong, can this result in the battery icon appearing right before emulationstation runs, and dissapear when it enters retropie ?, because i see the icon coming up for 1 sec and then it dissapears.
And last question is, can it be turned off and on (offcourse when all is installed correct) by pressing select for a few seconds ?

And @Helder, if you read this, i have few aio's from you, including the Red colored aio 2.2(32u4), but for some reason i get trouble programming it into HoolyHoo's Hex, i get several errors in avrdudes for some reason it can't set the fuses, but when i reprogram it back to your Hex files, all goes perfect and no errors, only that Hex from HoolyHoo, and @ the white aio's there's no trouble flashing it into these Hex files.. (all connections are properly)

Thanks in advance, 144Tech

cat /etc/rc.local

HoolyHoo wrote: ↑

Sun Aug 20, 2017 12:53 pm

144TECH wrote: ↑

Sun Aug 20, 2017 12:27 pm

Type at the command line:

Code: Select all

cat /etc/rc.local

And show me the output.

144TECH wrote: ↑

Sun Aug 20, 2017 1:25 pm

HoolyHoo wrote: ↑

Sun Aug 20, 2017 12:53 pm

144TECH wrote: ↑

Sun Aug 20, 2017 12:27 pm

Type at the command line:

Code: Select all

cat /etc/rc.local

And show me the output.

Okay, will post it here later, today's my birthday so not so much time, but i really like to know what causes the battery icon to lit up one time and dissapear, could it be in that last line ? because i swear i did make no mistakes installing, except that last line.
But when i sudo that one, like my post above it should be fine, haven't tested that yet.
I'll let you know.
Thank you very much

HoolyHoo wrote: ↑

Sun Aug 20, 2017 1:34 pm

144TECH wrote: ↑

Sun Aug 20, 2017 1:25 pm

HoolyHoo wrote: ↑

Sun Aug 20, 2017 12:53 pm

Type at the command line:

Code: Select all

cat /etc/rc.local

And show me the output.

Code: Select all

#!/bin/sh -e
#
# rc.local
#
# This script is executed at the end of each multiuser runlevel.
# Make sure that the script will "exit 0" on success or any other
# value on error.
#
# In order to enable or disable this script just change the execution
# bits.
#
# By default this script does nothing.

# Print the IP address
_IP=$(hostname -I) || true
if [ "$_IP" ]; then
  printf "My IP address is %s\n" "$_IP"
fi

/home/pi/gbzbatterymonitor/HHMonitorStart.sh &exit 0

144TECH wrote: ↑

Sun Aug 20, 2017 3:59 pm

HoolyHoo wrote: ↑

Sun Aug 20, 2017 1:34 pm

144TECH wrote: ↑

Sun Aug 20, 2017 1:25 pm

Code: Select all

#!/bin/sh -e
#
# rc.local
#
# This script is executed at the end of each multiuser runlevel.
# Make sure that the script will "exit 0" on success or any other
# value on error.
#
# In order to enable or disable this script just change the execution
# bits.
#
# By default this script does nothing.

# Print the IP address
_IP=$(hostname -I) || true
if [ "$_IP" ]; then
  printf "My IP address is %s\n" "$_IP"
fi

/home/pi/gbzbatterymonitor/HHMonitorStart.sh &exit 0

The last line should read exit 0, it seems like it was placed adjacent to the script launch command. Try editing it to where it's on the next line and see if it works.

HoolyHoo wrote: ↑

Sun Aug 20, 2017 4:50 pm

144TECH wrote: ↑

Sun Aug 20, 2017 3:59 pm

HoolyHoo wrote: ↑

Sun Aug 20, 2017 1:34 pm

The last line should read exit 0, it seems like it was placed adjacent to the script launch command. Try editing it to where it's on the next line and see if it works.

Okay, done that (i actually did this before too on several ways)
But what i get is that when the retropie picture starts while loading and right before it goes over into emulationstation i see the battery icon for 1 or 2 seconds, and after that it dissapears.. no matter what i do, it comes, and goes right before it enters emu station.
I also tried another aio and another pi, but again i cant do wget, it keeps saying certificate not trusted blablabla. and my certificates are already updated to recent ones so for that reason i did it manually, but i can't get it to work.. the icon comes and goes.
IDK what the hell is going on, because i preferred to do it with wget offcourse...
@Helder, at what speed should i write the hex, any advice? since this stuff is not mentioned in the tutorial, but basically says follow helder's steps for programming the hex.. lol
As for now, i'm really freaking out here .. any help is welcome..

Thanks guys

144TECH wrote: ↑

Sun Aug 20, 2017 5:22 pm

HoolyHoo wrote: ↑

Sun Aug 20, 2017 4:50 pm

144TECH wrote: ↑

Sun Aug 20, 2017 3:59 pm

The last line should read exit 0, it seems like it was placed adjacent to the script launch command. Try editing it to where it's on the next line and see if it works.

Okay, done that (i actually did this before too on several ways)
But what i get is that when the retropie picture starts while loading and right before it goes over into emulationstation i see the battery icon for 1 or 2 seconds, and after that it dissapears.. no matter what i do, it comes, and goes right before it enters emu station.
I also tried another aio and another pi, but again i cant do wget, it keeps saying certificate not trusted blablabla. and my certificates are already updated to recent ones so for that reason i did it manually, but i can't get it to work.. the icon comes and goes.
IDK what the hell is going on, because i preferred to do it with wget offcourse...
@Helder, at what speed should i write the hex, any advice? since this stuff is not mentioned in the tutorial, but basically says follow helder's steps for programming the hex.. lol
As for now, i'm really freaking out here .. any help is welcome..

Thanks guys

I hear you but no need to freak out, haha. Are you running this script with a successful flash of the hex on helders board? I'm asking because that was part #2 of your problem. It won't work without it.

If that's not the issue, then check to see if script is running after ES starts. You can check through the command line and type:

Code: Select all

ps aux | grep python

Then we can go from there.

HoolyHoo wrote: ↑

Sun Aug 20, 2017 5:32 pm

144TECH wrote: ↑

Sun Aug 20, 2017 5:22 pm

HoolyHoo wrote: ↑

Sun Aug 20, 2017 4:50 pm

I hear you but no need to freak out, haha. Are you running this script with a successful flash of the hex on helders board? I'm asking because that was part #2 of your problem. It won't work without it.

If that's not the issue, then check to see if script is running after ES starts. You can check through the command line and type:

Code: Select all

ps aux | grep python

Then we can go from there.

The flashing went correct (on this aio board, no errors in avrdudes)

Then we got :

Code: Select all

root       645  0.2  2.6   9996  6520 ?        S    17:58   0:03 python /home/pi                                                                             /gbzbatterymonitor/HHBatteryMonitor.py
root       646  2.0  4.6  32796 11692 ?        Sl   17:58   0:27 python /home/pi                                                                             /gbzbatterymonitor/HHShutdown.py
pi         905  0.0  0.8   4272  2036 pts/0    S+   18:21   0:00 grep --color=au                                                                             to python