How to Program Helder's All in One GBZ PCB with Arduino IDE

Discussion about other hardware (including other Pi-like boards)
Macx
Posts: 16
Joined: Mon Mar 13, 2017 9:01 am
Has thanked: 2 times
Been thanked: 4 times

Re: How to Program Helder's All in One GBZ PCB with Arduino IDE

Post by Macx » Fri Dec 28, 2018 1:47 am

VeteranGamer wrote:
Sun Dec 23, 2018 10:55 am


have you had a look here....

https://sudomod.com/forum/viewtopic.php?f=52&t=1185

there's a high chance this has been covered and hopefully resolved there.....



.
Thanks for pointing out👌🏻, I've swapped the USB pins and now it's only recognized as a USB HUB. I have no possibility to install another driver. What am I still doing wrong? Thank you in advance 🙂

User avatar
Helder
Trailblazer
Trailblazer
Posts: 2813
Joined: Thu May 05, 2016 8:33 am
Location: Rogers, AR
Has thanked: 1421 times
Been thanked: 3082 times

Re: How to Program Helder's All in One GBZ PCB with Arduino IDE

Post by Helder » Fri Dec 28, 2018 11:39 am

Macx wrote:
Fri Dec 28, 2018 1:47 am
Thanks for pointing out👌🏻, I've swapped the USB pins and now it's only recognized as a USB HUB. I have no possibility to install another driver. What am I still doing wrong? Thank you in advance 🙂


So it shows up as a usb hub? the nthat part is working but nothing else is showing up? like does it show a Leonardo USB GamePad? also where did you buy the board from? I haven't sold these in well over a year but RGN has been selling them and if you got them from him I'd ask for an exchange if the Atmega32u4 is not being recognized.

Might want to invest in a cheap $4 USBasp programmer to reprogram the MCU if it needs it.
My Sale Threads:

Retro PSU, 3.5A output!


Chat with me and other members


Don't contact me about obtaining my board files (as you will not get them). Don't contact me about any of my boards if they are sold out, they will be restocked as soon as I can get them.


Don't support thieves like ckliang who copied my AIO to resell and is now cloning the mintyPi, support the original creators and not the thieves!

Macx
Posts: 16
Joined: Mon Mar 13, 2017 9:01 am
Has thanked: 2 times
Been thanked: 4 times

Re: How to Program Helder's All in One GBZ PCB with Arduino IDE

Post by Macx » Sat Dec 29, 2018 1:06 pm

Helder wrote:
Fri Dec 28, 2018 11:39 am
Macx wrote:
Fri Dec 28, 2018 1:47 am
Thanks for pointing out👌🏻, I've swapped the USB pins and now it's only recognized as a USB HUB. I have no possibility to install another driver. What am I still doing wrong? Thank you in advance 🙂


So it shows up as a usb hub? the nthat part is working but nothing else is showing up? like does it show a Leonardo USB GamePad? also where did you buy the board from? I haven't sold these in well over a year but RGN has been selling them and if you got them from him I'd ask for an exchange if the Atmega32u4 is not being recognized.

Might want to invest in a cheap $4 USBasp programmer to reprogram the MCU if it needs it.
hello helder, I have the board directly from you (2017) ... that's all a while ago, I had a few private problems and often have to pause. yes you are right, only the usb hub is detected no gamepad or sound card. ... how big is the chance that it works with the programmer, then I buy me such a thing

thank you 🙂

User avatar
Helder
Trailblazer
Trailblazer
Posts: 2813
Joined: Thu May 05, 2016 8:33 am
Location: Rogers, AR
Has thanked: 1421 times
Been thanked: 3082 times

Re: How to Program Helder's All in One GBZ PCB with Arduino IDE

Post by Helder » Sat Dec 29, 2018 5:05 pm

Worth a shot and the programmer can be used for other boards that have similar arduino chips so it's not a waste of money.
My Sale Threads:

Retro PSU, 3.5A output!


Chat with me and other members


Don't contact me about obtaining my board files (as you will not get them). Don't contact me about any of my boards if they are sold out, they will be restocked as soon as I can get them.


Don't support thieves like ckliang who copied my AIO to resell and is now cloning the mintyPi, support the original creators and not the thieves!

Macx
Posts: 16
Joined: Mon Mar 13, 2017 9:01 am
Has thanked: 2 times
Been thanked: 4 times

Re: How to Program Helder's All in One GBZ PCB with Arduino IDE

Post by Macx » Sat Jan 05, 2019 12:51 pm

Hello everybody, I get this error. Is the board broken now, or do I have a chance to repair it?

BTW, Happy New Year :)
Attachments
failure.JPG
failure.JPG (112.68 KiB) Viewed 651 times

User avatar
Helder
Trailblazer
Trailblazer
Posts: 2813
Joined: Thu May 05, 2016 8:33 am
Location: Rogers, AR
Has thanked: 1421 times
Been thanked: 3082 times

Re: How to Program Helder's All in One GBZ PCB with Arduino IDE

Post by Helder » Sun Jan 06, 2019 4:47 pm

You sure you have it connected properly to the board? also hit the detect button first to see if it detects the atmega chip or not. If you wire it wrong then you may have damaged it especially if it was working at one time.
My Sale Threads:

Retro PSU, 3.5A output!


Chat with me and other members


Don't contact me about obtaining my board files (as you will not get them). Don't contact me about any of my boards if they are sold out, they will be restocked as soon as I can get them.


Don't support thieves like ckliang who copied my AIO to resell and is now cloning the mintyPi, support the original creators and not the thieves!

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest