sudomod

TheDeviantZen wrote: ↑

Fri Aug 18, 2017 1:48 am

Hi mates,
I can use a little of your help here.
I putted my mityPi together yesterday, everything was going fine. Did the first test (powering the pi0 with usb) like on the tutorial video, and it worked

After that I assembled all the parts together and now my mintypi wont turn on.

Some photosShow

Maybe I connected something on the wrong place :/ Can you help me?

Should my black wire from the switch be connected to the vcc?

Tomorrow I'll go on a vacation trip and would love to bring it with me.

VeteranGamer wrote: ↑

Fri Aug 18, 2017 1:55 am

you have also got a GND wire going to the switch.... i think that should be a 5v (VCC)


move the GND wire on the mintyPi board coming from the switch to the next point on the board (VCC)

TheDeviantZen wrote: ↑

Fri Aug 18, 2017 6:37 am

Yeah! that was the problem now it works just fine! thanks!

I noticed other problem
No sound. Do I have to change any option so I can have sound? What is the key combo to volume up and down?

wermy wrote: ↑

Fri Aug 18, 2017 7:03 am

TheDeviantZen wrote: ↑

Fri Aug 18, 2017 6:37 am

Yeah! that was the problem now it works just fine! thanks!

I noticed other problem
No sound. Do I have to change any option so I can have sound? What is the key combo to volume up and down?

Can you post some clearer images of the sound card and the usb pads on the bottom of the pi?

wermy wrote: ↑

Fri Aug 18, 2017 7:07 am

I'd look at your USB pads on the pi itself first - it's pretty common for people to accidentally bridge one of those with the usb port legs right next to it. It's really hard to tell from the pictures but it looks like your sound card itself is ok.

wermy wrote:You should have access to a folder on the SD card that’s named ‘boot’ (it’s actually a partition). Within there, there will be a file called “wpa_supplicant.conf”.

wermy wrote:Open it up with a text editor, and enter your wifi network name (SSID) where it says “SSID_GOES_HERE” (keep the quotes). Enter your wifi password where it says “WIFI_PASSWORD_GOES_HERE”. That’s it!

TheDeviantZen wrote: ↑

Thu Aug 31, 2017 7:51 am

wermy wrote: ↑

Fri Aug 18, 2017 7:07 am

I'd look at your USB pads on the pi itself first - it's pretty common for people to accidentally bridge one of those with the usb port legs right next to it. It's really hard to tell from the pictures but it looks like your sound card itself is ok.

Hi again!
Arrived from my vacation. So, I re-soldered everything again and the sound card now works fine.
That problem is now solved
Now I'm facing an other "problem", im trying to set my wifi network by following your tutorial steps. In there you say:

wermy wrote:You should have access to a folder on the SD card that’s named ‘boot’ (it’s actually a partition). Within there, there will be a file called “wpa_supplicant.conf”.

the only file I have its called "._wpa_supplicant.conf", should I delete the "._" ?
and than you say:

wermy wrote:Open it up with a text editor, and enter your wifi network name (SSID) where it says “SSID_GOES_HERE” (keep the quotes). Enter your wifi password where it says “WIFI_PASSWORD_GOES_HERE”. That’s it!

But when I open the file I have It only says: " Mac OS X 2 ° â ATTR;šÉÿ â ¨ * ¨ * $com.apple.metadata:_kMDItemUserTags bplist00  This resource fork intentionally left blank ÿÿ"

What should I do?
should I create a file named wpa_supplicant.conf? Can you send me your file so I have only to replace with my wifi ssid and password?

network={
    ssid="SSID_GOES_HERE"
    psk="WIFI_PASSWORD_GOES_HERE"
    key_mgmt=WPA-PSK
}