[For Sale, Preorder] DMG pre-cut cases

Sell or trade things with other forum members!
User avatar
dryja123
Posts: 1064
Joined: Tue May 09, 2017 5:34 pm
Location: Central NJ
Has thanked: 233 times
Been thanked: 552 times

Re: [interest check] DMG pre-cut cases

Post by dryja123 » Tue Jul 11, 2017 10:11 am

Looks good to me! Thanks

kubino
Posts: 205
Joined: Tue Mar 14, 2017 9:03 am
Has thanked: 54 times
Been thanked: 150 times

Re: [interest check] DMG pre-cut cases

Post by kubino » Tue Jul 11, 2017 10:57 am

dryja123 wrote:
Tue Jul 11, 2017 10:11 am
Looks good to me! Thanks
but if you're planning to use front LEDs you need modified bracket with holes :
Hoolyhoo_mod.png
Hoolyhoo_mod.png (19.51 KiB) Viewed 2688 times

Elmafioso90
Posts: 61
Joined: Thu Jun 01, 2017 3:09 pm
Has thanked: 26 times
Been thanked: 18 times

Re: [interest check] DMG pre-cut cases

Post by Elmafioso90 » Tue Jul 11, 2017 11:11 am

@kubino, would you mind to align the LED holes with Kite's SAIO so they can be seen from the upper part?

Since you have your test case you could try to see how they look with Hoolyhoo's bracket. I am going to use it too and would like to just assemble your case with all the other parts without further tweaking.

kubino
Posts: 205
Joined: Tue Mar 14, 2017 9:03 am
Has thanked: 54 times
Been thanked: 150 times

Re: [interest check] DMG pre-cut cases

Post by kubino » Tue Jul 11, 2017 11:21 am

Elmafioso90 wrote:
Tue Jul 11, 2017 11:11 am
@kubino, would you mind to align the LED holes with Kite's SAIO so they can be seen from the upper part?

Since you have your test case you could try to see how they look with Hoolyhoo's bracket. I am going to use it too and would like to just assemble your case with all the other parts without further tweaking.
I can draw it, but can't drill them by CNC :-( only possibility is front case at the moment.

Elmafioso90
Posts: 61
Joined: Thu Jun 01, 2017 3:09 pm
Has thanked: 26 times
Been thanked: 18 times

Re: [interest check] DMG pre-cut cases

Post by Elmafioso90 » Tue Jul 11, 2017 3:14 pm

Thanks as always for your fast reply.
I hope not to break Hoolyhoo's bracket while making the holes lol

exoboy
Posts: 8
Joined: Sat Jul 08, 2017 3:10 pm
Been thanked: 1 time

Re: [interest check] DMG pre-cut cases

Post by exoboy » Tue Jul 11, 2017 7:11 pm

kubino wrote:
Tue Jul 11, 2017 4:40 am
exoboy wrote:
Mon Jul 10, 2017 10:12 pm
Would like a grey one with kite SuperAIO USB and X/Y holes. Unsure about LED holes - in the example pic they're much larger than I would like.
ok, will put you in a list. The holes in picture are 3mm, but I can do 1.2mm radius or even smaller.
1.2mm sounds much better - I'd like to see the LEDs for status in case something goes wrong, but I don't need them quite so prominent.

Thanks, please let me know when you would be ready. Do you have any idea on lead time?

kubino
Posts: 205
Joined: Tue Mar 14, 2017 9:03 am
Has thanked: 54 times
Been thanked: 150 times

Re: [interest check] DMG pre-cut cases

Post by kubino » Wed Jul 12, 2017 12:57 am

exoboy wrote:
Tue Jul 11, 2017 7:11 pm

1.2mm sounds much better - I'd like to see the LEDs for status in case something goes wrong, but I don't need them quite so prominent.

Thanks, please let me know when you would be ready. Do you have any idea on lead time?
It can takes up to 4 weeks.

Elmafioso90
Posts: 61
Joined: Thu Jun 01, 2017 3:09 pm
Has thanked: 26 times
Been thanked: 18 times

Re: [interest check] DMG pre-cut cases

Post by Elmafioso90 » Wed Jul 12, 2017 1:57 pm

Just trying to give you ideas to polish the design.

Check this build:
http://www.sudomod.com/forum/viewtopic.php?f=9&t=3197

Would it be possible to countersink the holes through CNC? I know you stated that trying to give X/Y buttons the same look as original A/B is not convenient enough, hence this could look quite good.

Excuse that I ask too many questions about CNC milling but I'm like a kid in a candy shop with these newer technologies :)

kubino
Posts: 205
Joined: Tue Mar 14, 2017 9:03 am
Has thanked: 54 times
Been thanked: 150 times

Re: [interest check] DMG pre-cut cases

Post by kubino » Wed Jul 12, 2017 2:14 pm

Elmafioso90 wrote:
Wed Jul 12, 2017 1:57 pm
Just trying to give you ideas to polish the design.

Check this build:
http://www.sudomod.com/forum/viewtopic.php?f=9&t=3197

Would it be possible to countersink the holes through CNC? I know you stated that trying to give X/Y buttons the same look as original A/B is not convenient enough, hence this could look quite good.

Excuse that I ask too many questions about CNC milling but I'm like a kid in a candy shop with these newer technologies :)
that shoudn't be a problem with correct bit. In fact I already tried something similar :
P_20170712_220504.jpg
P_20170712_220504.jpg (847.98 KiB) Viewed 2628 times

User avatar
Chrisagu28
Posts: 101
Joined: Tue Mar 14, 2017 10:33 am
Has thanked: 41 times
Been thanked: 10 times

Re: [interest check] DMG pre-cut cases

Post by Chrisagu28 » Sat Jul 22, 2017 3:16 am

Did you use a standard countersink bit when you did your test? I would love to have that little taper/countersunk holes. It would put the cherry on top of my GBZ shell I get from you.

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest