Page 24 of 44
Re: [For Sale, Preorder] DMG pre-cut cases
Posted: Sat Oct 28, 2017 11:38 am
by J-Malice
petergr wrote: ↑Thu Oct 26, 2017 4:24 pm
1) Is the case compatible with the new Kite's Circuit Sword board? And especially if I add the USB cut and L1L2/R1R2 6mm buttons?
I am also wondering this, sort of. If anyone has used a case with this cut, were you able to figure out how to make it work with a raspberry pi3? If so, so you have a link to your show off thread with pictures? Would love to hear about it and how it was done.
Re: [For Sale, Preorder] DMG pre-cut cases
Posted: Sat Oct 28, 2017 12:30 pm
by dryja123
J-Malice wrote: ↑Sat Oct 28, 2017 11:38 am
petergr wrote: ↑Thu Oct 26, 2017 4:24 pm
1) Is the case compatible with the new Kite's Circuit Sword board? And especially if I add the USB cut and L1L2/R1R2 6mm buttons?
I am also wondering this, sort of. If anyone has used a case with this cut, were you able to figure out how to make it work with a raspberry pi3? If so, so you have a link to your show off thread with pictures? Would love to hear about it and how it was done.
I wasn't able to get this to work with a raspberry pi3, it sat on the button bracket. I ended up selling the case to another forum member.
It should work fine with the new circuit sword because that part of the case should be unobstructed.
Re: [For Sale, Preorder] DMG pre-cut cases
Posted: Sat Oct 28, 2017 2:32 pm
by Johnny sublime
Would it be possible to cut the bottom right corner of the screen square as much as I love the nostalgia of it I can't stand anything obstructing my view of a screen
Re: [For Sale, Preorder] DMG pre-cut cases
Posted: Sun Oct 29, 2017 5:08 am
by Seye
Interested in pre-ordering, sent pm please respond thanks.
Re: [For Sale, Preorder] DMG pre-cut cases
Posted: Mon Oct 30, 2017 11:39 am
by Juanje
Hello,
Im interested in a pre cut DMG-01 transparent case for Kites Circuit Sword, with USB cut, SNES style (4 butons) , an analog stick hole in the centre, and L1,2 and R1,2 bracket included.
Could it be possible to Preorder?
If so, how much would it cost, and when would I receive it?
Thx a lot
Re: [For Sale, Preorder] DMG pre-cut cases
Posted: Tue Oct 31, 2017 1:01 pm
by kubino
For Kite's new CS board I will offer cut's when is released, note now I have no access to this board and there might be slight difference in USB cut compared to other versions.
Re: [For Sale, Preorder] DMG pre-cut cases
Posted: Thu Nov 02, 2017 5:24 am
by gilbertotron
Kubino - did you manage to get the 640x480 screen cut outs to work?
Re: [For Sale, Preorder] DMG pre-cut cases
Posted: Thu Nov 02, 2017 8:18 am
by Rayman75
Pm sent for pre cut black case
Re: [For Sale, Preorder] DMG pre-cut cases
Posted: Sun Nov 05, 2017 2:52 am
by kubino
Rayman75 wrote: ↑Thu Nov 02, 2017 8:18 am
Pm sent for pre cut black case
PM Replied
Re: [For Sale, Preorder] DMG pre-cut cases
Posted: Sun Nov 05, 2017 2:54 am
by kubino
gilbertotron wrote: ↑Thu Nov 02, 2017 5:24 am
Kubino - did you manage to get the 640x480 screen cut outs to work?
yes, with some minor problems
(you can check in the bracket thread) Had no much time to work on it as lot of other stuffs appeared recently. But I'll definitively go back to it by end of next week.