[For Sale, Preorder] DMG pre-cut cases
- dryja123
- Posts: 1076
- Joined: Tue May 09, 2017 5:34 pm
- Location: Central NJ
- Has thanked: 239 times
- Been thanked: 553 times
Re: [interest check] DMG pre-cut cases
Looks good to me! Thanks
Guide for troubleshooting mintyPi power problems: http://www.sudomod.com/forum/viewtopic.php?f=34&t=4115
My mintyPi builds: http://www.sudomod.com/forum/viewtopic.php?f=32&t=3985
My mintyPi builds: http://www.sudomod.com/forum/viewtopic.php?f=32&t=3985
-
- Posts: 61
- Joined: Thu Jun 01, 2017 3:09 pm
- Has thanked: 26 times
- Been thanked: 18 times
Re: [interest check] DMG pre-cut cases
@kubino, would you mind to align the LED holes with Kite's SAIO so they can be seen from the upper part?
Since you have your test case you could try to see how they look with Hoolyhoo's bracket. I am going to use it too and would like to just assemble your case with all the other parts without further tweaking.
Since you have your test case you could try to see how they look with Hoolyhoo's bracket. I am going to use it too and would like to just assemble your case with all the other parts without further tweaking.
Re: [interest check] DMG pre-cut cases
I can draw it, but can't drill them by CNC only possibility is front case at the moment.Elmafioso90 wrote: ↑Tue Jul 11, 2017 11:11 am@kubino, would you mind to align the LED holes with Kite's SAIO so they can be seen from the upper part?
Since you have your test case you could try to see how they look with Hoolyhoo's bracket. I am going to use it too and would like to just assemble your case with all the other parts without further tweaking.
-
- Posts: 61
- Joined: Thu Jun 01, 2017 3:09 pm
- Has thanked: 26 times
- Been thanked: 18 times
Re: [interest check] DMG pre-cut cases
Thanks as always for your fast reply.
I hope not to break Hoolyhoo's bracket while making the holes lol
I hope not to break Hoolyhoo's bracket while making the holes lol
Re: [interest check] DMG pre-cut cases
1.2mm sounds much better - I'd like to see the LEDs for status in case something goes wrong, but I don't need them quite so prominent.
Thanks, please let me know when you would be ready. Do you have any idea on lead time?
-
- Posts: 61
- Joined: Thu Jun 01, 2017 3:09 pm
- Has thanked: 26 times
- Been thanked: 18 times
Re: [interest check] DMG pre-cut cases
Just trying to give you ideas to polish the design.
Check this build:
http://www.sudomod.com/forum/viewtopic.php?f=9&t=3197
Would it be possible to countersink the holes through CNC? I know you stated that trying to give X/Y buttons the same look as original A/B is not convenient enough, hence this could look quite good.
Excuse that I ask too many questions about CNC milling but I'm like a kid in a candy shop with these newer technologies
Check this build:
http://www.sudomod.com/forum/viewtopic.php?f=9&t=3197
Would it be possible to countersink the holes through CNC? I know you stated that trying to give X/Y buttons the same look as original A/B is not convenient enough, hence this could look quite good.
Excuse that I ask too many questions about CNC milling but I'm like a kid in a candy shop with these newer technologies
Re: [interest check] DMG pre-cut cases
that shoudn't be a problem with correct bit. In fact I already tried something similar :Elmafioso90 wrote: ↑Wed Jul 12, 2017 1:57 pmJust trying to give you ideas to polish the design.
Check this build:
http://www.sudomod.com/forum/viewtopic.php?f=9&t=3197
Would it be possible to countersink the holes through CNC? I know you stated that trying to give X/Y buttons the same look as original A/B is not convenient enough, hence this could look quite good.
Excuse that I ask too many questions about CNC milling but I'm like a kid in a candy shop with these newer technologies
- Chrisagu28
- Posts: 101
- Joined: Tue Mar 14, 2017 10:33 am
- Has thanked: 41 times
- Been thanked: 10 times
Re: [interest check] DMG pre-cut cases
Did you use a standard countersink bit when you did your test? I would love to have that little taper/countersunk holes. It would put the cherry on top of my GBZ shell I get from you.
Who is online
Users browsing this forum: No registered users and 1 guest