Page 5 of 6

Re: Gaboze Pocaio

Posted: Mon Oct 15, 2018 3:22 am
by spacemishka
lukesky333 wrote:
Thu Oct 11, 2018 8:14 am
Is it possible to use a Banana Pi Zero instead of a Raspberry Pi Zero? It should have the same size but a lot more power?

I've one more question:
I try to order all needed parts for the PCB. Is it needed, that the resistors have a tolerance of 0.1%? I'm from Europe and an order from Digikey is very expensive. Is it possible to get all these parts from Aliexpress too?
Not only it requires more power, banana pi need also active cooling

Re: Gaboze Pocaio

Posted: Wed Nov 07, 2018 7:29 am
by lukesky333
Thanks for the info...

I've another question:
Has anybody a actual shopping list for aliexpress? Digiverse orders Austria are to expensive so I want to order the parts from aliexpress. I've found a lot, but I need suggestions for the Micro-USB-connector and the battery.

Re: Gaboze Pocaio

Posted: Sat Nov 10, 2018 9:39 am
by YaYa
Hello sudoers !

Just to let you know that i did a small batch of stickers for the GABOZE to have something custom into your hands.
The link to the product page https://yaya-design.com/index.php/categ ... een-detail
Cartridge-GABOZE-POCAIO-platform-picture.jpg
Cartridge-GABOZE-POCAIO-platform-picture.jpg (4.25 MiB) Viewed 14328 times
GBP-GABOZE-POCAIO-platform-picture.jpg
GBP-GABOZE-POCAIO-platform-picture.jpg (4.54 MiB) Viewed 14328 times

Re: Gaboze Pocaio

Posted: Wed Dec 05, 2018 8:55 am
by lukesky333
Hi,

the WIKI is offline - why? I've ordered all parts and need now further instructions from the wiki.

Please help me!!!

Re: Gaboze Pocaio

Posted: Thu Dec 06, 2018 6:04 am
by lukesky333
lukesky333 wrote:
Wed Dec 05, 2018 8:55 am
Hi,

the WIKI is offline - why? I've ordered all parts and need now further instructions from the wiki.

Please help me!!!
Ok, I've found it... The project was renamed, so no link was working anymore.

Wiki

Re: Gaboze Pocaio

Posted: Tue Dec 11, 2018 6:50 pm
by CornholioGSM
hello, i am new here....and new on pi zero :)
i have one question - can i use another TFT display?
I want to fit inside pocket 2.8" 640X480 TFT display with 60+ fps marked as MZDPI_VGA_ZERO.
This display have better resolution and maybe better colors.
is possible to use it with some wiring?

Re: Gaboze Pocaio

Posted: Fri Dec 14, 2018 4:23 am
by VeteranGamer
CornholioGSM wrote:
Tue Dec 11, 2018 6:50 pm
hello, i am new here....and new on pi zero :)
i have one question - can i use another TFT display?
I want to fit inside pocket 2.8" 640X480 TFT display with 60+ fps marked as MZDPI_VGA_ZERO.
This display have better resolution and maybe better colors.
is possible to use it with some wiring?
short anwser.....

NO


that screen uses DPI, and this build/project uses SPI
(completely different wiring/setup)


.

Re: Gaboze Pocaio

Posted: Wed Jan 16, 2019 6:38 am
by lukesky333
I can't find the image for the GABOZE Pocaio anymore... Please give me the link to the image for installation....

Thanks!

Re: Gaboze Pocaio

Posted: Thu Jan 17, 2019 8:58 am
by rodocop
lukesky333 wrote:
Wed Jan 16, 2019 6:38 am
I can't find the image for the GABOZE Pocaio anymore... Please give me the link to the image for installation....

Thanks!
hmm, can't seem to find one for the original Gaboze, might have to make your own, see the links. Use a base 4.4 image.

Screen set up:
https://github.com/32teeth/GabozePocaio ... FT-Display
PWM audio setup:
https://github.com/32teeth/GabozePocaio ... M-Settings
Button setup:
Install retrogame using adafruits guide, and then see the proper values to add to the retroarch.cfg
https://github.com/32teeth/GabozePocaio ... 8Manual%29

Re: Gaboze Pocaio

Posted: Fri May 29, 2020 10:59 pm
by superbuzz
Not sure if this is the best place to post this (necro necro necro lol)

So I finally decided to order more parts and build the round 2 boards (PCBs been sitting there a while).

Had a look on Aliexpress for the LCD and I can't find any listings of the 51 pin LCD around anymore!
Anyone have any leads on the LCD? Or is there a way to get the 30-something pin ones (seems like 36,37,38 pin variants) working on the board?

I also have the Pocket FE boards waiting to be built (yeah *finally* got the stuff like over a year later... ha - I think they use the same LCDs too =/)