Page 2 of 2

Re: Johweb's build (WIP)

Posted: Mon Sep 26, 2016 1:23 pm
by smithincanton
That's a neat idea about getting audio out of the PiZ! I bought that same screen off of ebay and I can't wait to take a look at it in person. Looks amazing in photos. Your build is looking awesome!

Re: Johweb's build (WIP)

Posted: Mon Sep 26, 2016 1:35 pm
by johweb
Thanks ! But I'm just mixing ideas from other builds... ;)
No update of my build last week-end because I didn't have time to work on it (and I can only spend time on week-ends...)

Re: Johweb's build (WIP)

Posted: Sun Oct 02, 2016 10:28 am
by johweb
Let's keep building !

I received my battery, an after a little trim of the DMG battery compartment, it fits perfectly. Sorry, I forgot to take a picture, I'll do it next week.

I soldered cable onto the prs_tech board :
IMG_20161001_154802.jpg
IMG_20161001_154802.jpg (132.47 KiB) Viewed 12183 times
I made the screen pcb lighter than it was, removing connectors and soldering directly :
IMG_20161001_154743.jpg
IMG_20161001_154743.jpg (122.7 KiB) Viewed 12183 times
In a first time, I only wanted 4 front buttons. But then, I found an old USB joystick "sleeping" in a room of my house. So I decided to take L1 and R1 from it to put them in the back of the DMG case :
IMG_20161001_154859.jpg
IMG_20161001_154859.jpg (82.81 KiB) Viewed 12183 times
I also took the board from the old joystick, I had to trim it a lot !
IMG_20161001_154916.jpg
IMG_20161001_154916.jpg (94.04 KiB) Viewed 12183 times
Using a 3D printer, I made a simple part to maintain these back buttons :
IMG_20161001_154945.jpg
IMG_20161001_154945.jpg (58.67 KiB) Viewed 12183 times
Before going further, I wanted to check my screen cables.
IMG_20161002_102451.jpg
IMG_20161002_102451.jpg (148.91 KiB) Viewed 12183 times
Cool ! Everything's fine for now...

I made most of this yesterday and this morning. And I was very pleased because Camble's graceful shutdown's switch was in my mailbox !
So, next time's plan :
- test the switch, then glue it in place
- make the hdmi cable smaller to fit in the case (and yes, test again if everything's right)
- planning how everything will fit inside and preparing hot glue ! :mrgreen:

Re: Johweb's build (WIP)

Posted: Mon Oct 10, 2016 12:41 pm
by smithincanton
johweb wrote: In a first time, I only wanted 4 front buttons. But then, I found an old USB joystick "sleeping" in a room of my house. So I decided to take L1 and R1 from it to put them in the back of the DMG case :
IMG_20161001_154859.jpg
Oh man...I really like those L/R buttons. I might have to hit up the goodwill and see if I can find a controller to salvage. Looks REALLY clean! Loving your build!

Re: Johweb's build (WIP)

Posted: Mon Oct 10, 2016 1:21 pm
by triticus
Do you actually need all those wires coming off the screen board? Can't you just connect it like the smaller screens with the single yellow wire to the TV through hold on the Pi?

Is that providing a better quality video signal with all of that in there?

Re: Johweb's build (WIP)

Posted: Mon Oct 10, 2016 1:25 pm
by johweb
I just wanted to use hdmi. But I had problems last week-end, trying to shorten this cable. So I'm now using the composite cable. I didn't update my build, I first want to resolve a few problems first.

Re: Johweb's build (WIP)

Posted: Sun Oct 23, 2016 6:04 pm
by zspyked
Digging the beveled button holes you did. It's always cool to see new ideas and tweaks that improve these builds. :D

Re: Johweb's build (WIP)

Posted: Tue Dec 20, 2016 10:16 pm
by johweb
Hey ! My build's not dead !
I've been struggling for a long time with the safe shutdown switch. So I ended by making my own, using the guide.

Now, my build is almost complete, I'll make pictures and I'll update this post next week !
:D

Re: Johweb's build (WIP)

Posted: Sun Jan 08, 2017 12:42 am
by dklutie24
Needing to test my audio but not sure how to without the games loaded on there and no controller hooked up to the pi. What is this "speaker test" command? Might need to try this myself

Re: Johweb's build (WIP)

Posted: Mon Jan 30, 2017 2:28 am
by Enix
@johweb
Can we get an update on your project?
I am using the same screen. Was curious where you get the audio from? From the hmdi to vga converter? How did everything fit? Would appreciate more photos.
Thank you!