Black and Translucent Red CM3

Show off your completed Game Boy Zero, or post your build logs here!
Post Reply
dasfool
Posts: 19
Joined: Sat Aug 05, 2017 9:33 pm
Has thanked: 4 times
Been thanked: 6 times

Black and Translucent Red CM3

Post by dasfool » Sat Jul 14, 2018 2:06 pm

I spent a lot of time deciding on a color scheme. I'm happy with how this little guy turned out.
20180714_113534_res.jpg
Money Shot
20180714_113534_res.jpg (666.61 KiB) Viewed 1627 times
Parts List: How I filled the LED holes
View MoreShow
20180714_113801_res.jpg
Rear
20180714_113801_res.jpg (569.16 KiB) Viewed 1627 times
20180714_113607_res.jpg
Battery
20180714_113607_res.jpg (533.24 KiB) Viewed 1627 times
20180714_113627_res.jpg
Side: SD/Mode/USB-C
20180714_113627_res.jpg (297.1 KiB) Viewed 1627 times
20180714_113650_res.jpg
Side: USB/HDMI
20180714_113650_res.jpg (306.56 KiB) Viewed 1627 times
20180714_113740_res.jpg
Front with Screen Off
20180714_113740_res.jpg (491.63 KiB) Viewed 1627 times
20180714_113755_res.jpg
Top
20180714_113755_res.jpg (401.59 KiB) Viewed 1627 times
20180713_225722_res.jpg
Lights at Night
20180713_225722_res.jpg (305.09 KiB) Viewed 1627 times
Last edited by dasfool on Tue Jul 17, 2018 2:37 am, edited 2 times in total.

dasfool
Posts: 19
Joined: Sat Aug 05, 2017 9:33 pm
Has thanked: 4 times
Been thanked: 6 times

Re: Black and Translucent Red CM3

Post by dasfool » Mon Jul 16, 2018 10:16 am

Update:

I ended up replacing the NES buttons and D-pad with classic Gameboy ones. The buttons sat just a little too low and were a bit uncomfortable to use. DMG ones feel great. The D-pad I liked but I couldn't feel that nicely defined "popping" that you get when depressing the membrane. I get a better feel when using the DMG one.

I also seemed to have wired the analog incorrectly and wound up in the same situation as another forum member where everything seemed to work fine accept diagonal down right wouldn't register. Rerouting the wires fixed it.

Lastly, I went with a darker grey for the start and select button membrane. The ones from Retro Modding are nice and they feel a bit harder and less mushy than the ones included with most DMG cases.

Edit: Added images with the changes.
After ChangesShow
20180719_235027_res.jpg
Complete
20180719_235027_res.jpg (616.12 KiB) Viewed 1419 times
20180719_235005_res.jpg
Front Inputs
20180719_235005_res.jpg (891.65 KiB) Viewed 1419 times
Last edited by dasfool on Fri Jul 20, 2018 1:04 am, edited 1 time in total.

dasfool
Posts: 19
Joined: Sat Aug 05, 2017 9:33 pm
Has thanked: 4 times
Been thanked: 6 times

Re: Black and Translucent Red CM3

Post by dasfool » Fri Jul 20, 2018 12:27 am

I found a few more pictures on my phone that I thought may be useful for some.

Here's the fan, fan cartridge and the screws I used to secure them together:
Fan and Fan CartridgeShow
20180703_191912_res.jpg
Fan Attached
20180703_191912_res.jpg (511.76 KiB) Viewed 1421 times
20180703_191902_res.jpg
Screws Used for Fan
20180703_191902_res.jpg (655.29 KiB) Viewed 1421 times

Here's the back of the case showing the fit of the Power board with support bracket securing in the fan cartridge and everything fitting with the back button board:
The BackShow
20180703_204123_res.jpg
Fan and Fan cable extension, Power Support Bracket, and Back Button Board
20180703_204123_res.jpg (495.14 KiB) Viewed 1421 times

I used clamps to keep anything from moving, ensuring the epoxy cured well. The epoxy package said something about it setting in 5 minutes, but you really want to make sure you let it cure at least over night. Also this stuff smells awful so do it somewhere well ventilated. I don't have it pictured here, but on the other side of the case (the front), I have the plastic screen protector that came with the Gameboy case in place to keep the clamps from clamping directly to the screen and likely damaging it. I originally bought clamps from Home Depot, but the clamping force was really strong and I worried about it bending or marring the case. I found these cheap plastic clamps from Harbor Freight that were perfect for the job since the clamping force was much lighter.
Gluing the screenShow
20180704_194619_res.jpg
Securing the LCD and Screen Bracket with Clear Epoxy
20180704_194619_res.jpg (622.67 KiB) Viewed 1421 times

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest