BW 3.5 TFT LCD - 5V modification
-
- Posts: 1
- Joined: Sun Oct 07, 2018 8:48 am
BW 3.5 TFT LCD - 5V modification
Hi all,
I just started my first try on a GameBoy Zero.
Therefore i purchased this 3.5 inch tft lcd display from BW:
(https://www.amazon.de/KFZ-R%C3%BCckfahr ... op?ie=UTF8)
My problem here is, that the board doesn't fit any I found online.
It's similar to a Variant 2 but not really the same.
https://www.sudomod.com/wiki/index.php/GBZ_Screen
I've connected the display to 12V and 5V and measured out the voltage values on the chip, I suppose, is the DC/DC-converter.
In most guides the DC/DC-Converter is skipped by just connecting 5V to the VOUT pin.
My version however only has 4V output. I'm afraid that I will damage the board by connecting 5V to the pin I measured 4V.
If anyboy is able to help me I would be really glad.
Thank you for your answers!
Greetings
schnauzbartS
I just started my first try on a GameBoy Zero.
Therefore i purchased this 3.5 inch tft lcd display from BW:
(https://www.amazon.de/KFZ-R%C3%BCckfahr ... op?ie=UTF8)
My problem here is, that the board doesn't fit any I found online.
It's similar to a Variant 2 but not really the same.
https://www.sudomod.com/wiki/index.php/GBZ_Screen
I've connected the display to 12V and 5V and measured out the voltage values on the chip, I suppose, is the DC/DC-converter.
In most guides the DC/DC-Converter is skipped by just connecting 5V to the VOUT pin.
My version however only has 4V output. I'm afraid that I will damage the board by connecting 5V to the pin I measured 4V.
If anyboy is able to help me I would be really glad.
Thank you for your answers!
Greetings
schnauzbartS
-
- Posts: 5
- Joined: Mon Jun 05, 2017 6:15 am
- Has thanked: 3 times
Re: BW 3.5 TFT LCD - 5V modification
Hi,
I have the same issue.
Screen arrived today, opened it and the board didn't mach with any of the ones in the guides.
I used the ling from variant 1 to amazon.co.uk.
If anyone could share there methodes of how they found out where to solder, that may be a start...
I have the same issue.
Screen arrived today, opened it and the board didn't mach with any of the ones in the guides.
I used the ling from variant 1 to amazon.co.uk.
If anyone could share there methodes of how they found out where to solder, that may be a start...
Re: BW 3.5 TFT LCD - 5V modification
Hi,
I got the same bw screen today. It seems that this is the new model. Has someone success in powering these with 5v ?
I got the same bw screen today. It seems that this is the new model. Has someone success in powering these with 5v ?
-
- Posts: 226
- Joined: Tue Jan 31, 2017 11:06 am
- Location: Tianjin / China
- Has thanked: 25 times
- Been thanked: 53 times
Re: BW 3.5 TFT LCD - 5V modification
What you measure on the chip output could be some rest of AC ripple. Try to measure on the big capacitor on the picture bottom. There you should get something closure to 5V. You can inject your 5V as well on this cap. Take care: if you measure something close to 3.3V DO NOT inject 5V there!
Re: BW 3.5 TFT LCD - 5V modification
Hi mcgiver,
Thanks for your Reply. Im a Newby with this. But i will Try this today and give Feedback. I have just one question left: with wich voltage do i have to test this? I guess i must try this with 12v and when i get 5v on the cap i must solder the output to the plus on the board and Switch to 5v input with(hopefully) nice picture in the screen whitout flickering correct?
Thanks again!
EDIT: Ive quickly checked this.with 12v input there are 4.01V on the cap output. Dont know if this a good or bad value. I will wait for an answer till i Continue.
Thanks for your Reply. Im a Newby with this. But i will Try this today and give Feedback. I have just one question left: with wich voltage do i have to test this? I guess i must try this with 12v and when i get 5v on the cap i must solder the output to the plus on the board and Switch to 5v input with(hopefully) nice picture in the screen whitout flickering correct?
Thanks again!
EDIT: Ive quickly checked this.with 12v input there are 4.01V on the cap output. Dont know if this a good or bad value. I will wait for an answer till i Continue.
Re: BW 3.5 TFT LCD - 5V modification
Hi,
Ive put the ground on the board ground.was this wrong?
I measure anywhere on the board either 12v or 4v. It looks to me as if this board runs with 4v. Is that possible? If so, can the screen operate with the 5v from Rasperry?
Ive put the ground on the board ground.was this wrong?
I measure anywhere on the board either 12v or 4v. It looks to me as if this board runs with 4v. Is that possible? If so, can the screen operate with the 5v from Rasperry?
- Attachments
-
- 20181201_141816.jpg (7.98 MiB) Viewed 6926 times
- Le Nerdarto
- Posts: 10
- Joined: Thu Jun 15, 2017 3:12 am
- Location: stuttgart germany
- Has thanked: 2 times
- Been thanked: 5 times
- Contact:
Re: BW 3.5 TFT LCD - 5V modification
im at the same point on this project with the same screen and board right now....
if I make any progress i will report...
if someone gets it running on 5v, help would be appreciated
if I make any progress i will report...
if someone gets it running on 5v, help would be appreciated
- brainslugs83
- Posts: 8
- Joined: Mon Dec 03, 2018 1:56 pm
- Location: Bothell, WA, USA
- Has thanked: 12 times
- Been thanked: 1 time
- Contact:
Re: BW 3.5 TFT LCD - 5V modification
Sometimes voltage drops if there is load on the line -- I wouldn't be surprised if the 4v you're measuring is really 5v, but there is a load on it (e.g. it's driving the screen, so it drops a volt). -- You could try running the screen directly off of 5v -- and if it's dim, try temporarily bridging to one of the 4v spots and seeing if it gets bright (e.g. with an alligator clip or something).
Note 1: if it doesn't fix the dimness issue, disconnect it immediately, those are not the traces you're looking for!
Note 2: Beware, that could totally let the magic smoke out of the device, especially if you're not careful, so do it at your own risk...
Note 3: the little 8-pin DIL chip (two components above the big tin can cap that you're probing) looks a lot like the voltage regulator from some of the mod guides -- I would probe some of those pins to see if any of those are 5v... / there's also that 35v filter cap above (probably just a buffer for the input voltage, but it's worth probing).
Note 1: if it doesn't fix the dimness issue, disconnect it immediately, those are not the traces you're looking for!
Note 2: Beware, that could totally let the magic smoke out of the device, especially if you're not careful, so do it at your own risk...
Note 3: the little 8-pin DIL chip (two components above the big tin can cap that you're probing) looks a lot like the voltage regulator from some of the mod guides -- I would probe some of those pins to see if any of those are 5v... / there's also that 35v filter cap above (probably just a buffer for the input voltage, but it's worth probing).
-
- Posts: 5
- Joined: Mon Jun 05, 2017 6:15 am
- Has thanked: 3 times
Re: BW 3.5 TFT LCD - 5V modification
I did try to run it on 5v, but the backlight just goes on and of the whole time.
No picture shows up either...
No picture shows up either...
Who is online
Users browsing this forum: No registered users and 1 guest