Hi
I have what looks to be yet another variation screen so was just wondering about the wiring. I'm very new to all this so please excuse me if this has already been resolved elsewhere in the forum.
From my research (https://www.sudomod.com/forum/viewtopic.php?f=44&t=8266 and https://www.youtube.com/watch?v=_MtN_s4 ... u.be&t=230) I believe I need to bridge the input wire to pin 1 of the XL1509 chip as shown in the images.
Do i have this right?
If not what would be the correct wiring?
Many thanks
Variant Screen Wiring
- tinkerBOY
- Posts: 710
- Joined: Tue May 30, 2017 4:00 am
- Has thanked: 294 times
- Been thanked: 206 times
Re: Variant Screen Wiring
Check my post about GearBest Screen 5v Mod which uses the same XL1509 chip.
New! tinkerBOY PowerSwitch v1.0 with Safe Shutdown
Game Boy Zero Controllers available @ tinkerBOY.xyz * Support
tinkerBOY Controller v3.0 - built-in usb controller, usb audio, and usb hub
tinkerBOY Controller v2.0 - GPIO buttons and builtin PWM Audio and Amplifier
tinkerBOY Controller v1.1 - simple pcb button
* DPI Adapter - better display for GBZ
* keyboard converters - IBM XT/AT Soarer's Converter | ADB to USB Converter
Game Boy Zero Controllers available @ tinkerBOY.xyz * Support
tinkerBOY Controller v3.0 - built-in usb controller, usb audio, and usb hub
tinkerBOY Controller v2.0 - GPIO buttons and builtin PWM Audio and Amplifier
tinkerBOY Controller v1.1 - simple pcb button
* DPI Adapter - better display for GBZ
* keyboard converters - IBM XT/AT Soarer's Converter | ADB to USB Converter
- rodocop
- Posts: 1723
- Joined: Mon Aug 22, 2016 3:14 pm
- Location: Saskatchewan
- Has thanked: 606 times
- Been thanked: 608 times
Re: Variant Screen Wiring
Tinker boy is right, check out his link too.
I also just posted in another thread, but you want pin 2, not pin 1.
Pin 1 is for VIN, while pin 2 is the output.
https://imgur.com/a/9nZzwLx
Where the little divot on the chip is should be leg 1. Someone correct me if I am wrong.
I also just posted in another thread, but you want pin 2, not pin 1.
Pin 1 is for VIN, while pin 2 is the output.
https://imgur.com/a/9nZzwLx
Where the little divot on the chip is should be leg 1. Someone correct me if I am wrong.
_____________________________________________________
My Minty Pi builds:
http://www.sudomod.com/forum/viewtopic.php?f=32&t=3628
My GBZ builds:
http://www.sudomod.com/forum/viewtopic. ... 813#p50813
My modded DMG-01's:
http://www.sudomod.com/forum/viewtopic.php?f=13&t=2696
My NESpi:
http://www.sudomod.com/forum/viewtopic.php?f=13&t=2941
My Gaboze Pocaio's
https://sudomod.com/forum/viewtopic.php?f=13&t=6063
My Minty Pi builds:
http://www.sudomod.com/forum/viewtopic.php?f=32&t=3628
My GBZ builds:
http://www.sudomod.com/forum/viewtopic. ... 813#p50813
My modded DMG-01's:
http://www.sudomod.com/forum/viewtopic.php?f=13&t=2696
My NESpi:
http://www.sudomod.com/forum/viewtopic.php?f=13&t=2941
My Gaboze Pocaio's
https://sudomod.com/forum/viewtopic.php?f=13&t=6063
Who is online
Users browsing this forum: No registered users and 1 guest