Freeze after a couple of seconds
Freeze after a couple of seconds
Hi Guys,
I am a bit new to this, but I finished my project know completely.
The problem is, when I switch my Boy on, it boots up normally, but after a while it freezes (seconds, maybe 20-30). It happens normally when I try to setup the button configuration, or maybe in a another state. As faster I am, the more buttons I can setup. To switch it off, I have to pull out the battery.
Is there a short somewhere or something else !?
Hope someone can help.
And sorry, English is not my nativ language.
I am a bit new to this, but I finished my project know completely.
The problem is, when I switch my Boy on, it boots up normally, but after a while it freezes (seconds, maybe 20-30). It happens normally when I try to setup the button configuration, or maybe in a another state. As faster I am, the more buttons I can setup. To switch it off, I have to pull out the battery.
Is there a short somewhere or something else !?
Hope someone can help.
And sorry, English is not my nativ language.
-
- Posts: 226
- Joined: Tue Jan 31, 2017 11:06 am
- Location: Tianjin / China
- Has thanked: 25 times
- Been thanked: 53 times
Re: Freeze after a couple of seconds
You should try to reload the raspberry image.
Or: use another SD card
Or: did you changed any overclocking settings inside of config.txt?
This could be at worst a faulty raspberry!
Or: use another SD card
Or: did you changed any overclocking settings inside of config.txt?
This could be at worst a faulty raspberry!
- kite
- Posts: 972
- Joined: Thu May 12, 2016 4:30 am
- Location: UK
- Has thanked: 246 times
- Been thanked: 361 times
- Contact:
Re: Freeze after a couple of seconds
Is it the CS Lite, or the CS with the CM3? Does the Pi get hot during boot up?
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Re: Freeze after a couple of seconds
Hi Kite,
you remember me … its the board (CS CM3)you had in your hands a couple of days/week ago (Bastian from Germany). You Setup everything (you Changed the Pi3 CM3, updated the Ardunio) . The only Change I made in the Settings, was setting the Resolution to 640 x 480 and solder the Bridge on the board for the boost of the Display.
I will check later if its getting hot on boot up. But I mean, its getting hot.
Thanks
you remember me … its the board (CS CM3)you had in your hands a couple of days/week ago (Bastian from Germany). You Setup everything (you Changed the Pi3 CM3, updated the Ardunio) . The only Change I made in the Settings, was setting the Resolution to 640 x 480 and solder the Bridge on the board for the boost of the Display.
I will check later if its getting hot on boot up. But I mean, its getting hot.
Thanks
Re: Freeze after a couple of seconds
So... it’s getting warm to hot after about 2-3 Minutes. I can still touch the heatsink, but in my opinion it’s very warm for doing nothing than freeze.
I didn’t solder the Fan for now, is it because of that, I think no, or !?
I didn’t solder the Fan for now, is it because of that, I think no, or !?
- kite
- Posts: 972
- Joined: Thu May 12, 2016 4:30 am
- Location: UK
- Has thanked: 246 times
- Been thanked: 361 times
- Contact:
Re: Freeze after a couple of seconds
If you don't have it inside a case/enclosure, does it still do this?
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Re: Freeze after a couple of seconds
Ok ... it’s doing the same, but I think it’s not getting this hot outside of the shell, maybe it was the same before.
But I figured out that it’s not freezing befor I try to setup the buttons.
Emulation Station setup says „Hold a button to start“ ... in this State it won’t freeze, I can reply this (hold a button) and Release before the Message with the Arduino etc disappeared. Only after a while it freezes, when I try to setup the buttons. Maybe there is something wrong with the Arduino ?!
I don’t know
But I figured out that it’s not freezing befor I try to setup the buttons.
Emulation Station setup says „Hold a button to start“ ... in this State it won’t freeze, I can reply this (hold a button) and Release before the Message with the Arduino etc disappeared. Only after a while it freezes, when I try to setup the buttons. Maybe there is something wrong with the Arduino ?!
I don’t know
- kite
- Posts: 972
- Joined: Thu May 12, 2016 4:30 am
- Location: UK
- Has thanked: 246 times
- Been thanked: 361 times
- Contact:
Re: Freeze after a couple of seconds
Do you have another SD that you are able to try? And to confirm you are using the right image specifically for the Circuit Sword (not the Lite)?
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Re: Freeze after a couple of seconds
I put a fresh Image on the stick and now it’s working... thank you.
Back to the temperature, is it normal that without Fan the temperature is always around 60 Celsius ?
Back to the temperature, is it normal that without Fan the temperature is always around 60 Celsius ?
- kite
- Posts: 972
- Joined: Thu May 12, 2016 4:30 am
- Location: UK
- Has thanked: 246 times
- Been thanked: 361 times
- Contact:
Re: Freeze after a couple of seconds
Ok cool, perhaps there was something wrong with that SD, keep an eye on it on your new one and let me know if it changes!
60*C is fine, no issues there
60*C is fine, no issues there
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/
Who is online
Users browsing this forum: No registered users and 1 guest