Analog volume wheel doesn´t work

User avatar
kite
Posts: 972
Joined: Thu May 12, 2016 4:30 am
Location: UK
Has thanked: 246 times
Been thanked: 361 times
Contact:

Re: Analog volume wheel doesn´t work

Post by kite » Tue Jun 26, 2018 9:10 am

Any of the ones that use "B" .. when you rotate the volume wheel does it change the value on multimeter?
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/


ImageImageImageImageImage

SuperPitendo
Posts: 13
Joined: Fri Mar 09, 2018 7:08 am
Been thanked: 2 times

Re: Analog volume wheel doesn´t work

Post by SuperPitendo » Tue Jun 26, 2018 10:45 am

Yes!

A to B:
It changes the value from 0.00 at volume 0% to 9.32 at volume 100%

B to C:
same but reverse

User avatar
kite
Posts: 972
Joined: Thu May 12, 2016 4:30 am
Location: UK
Has thanked: 246 times
Been thanked: 361 times
Contact:

Re: Analog volume wheel doesn´t work

Post by kite » Wed Jun 27, 2018 4:51 am

ok, that all sounds perfect! So the pot works. Can you plug it in with the wires and turn it on.. put the pot to approx the middle, and measure the VOLTAGE from point A to C, and then the voltage from A to B (and C to B for the fun of it).
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/


ImageImageImageImageImage

SuperPitendo
Posts: 13
Joined: Fri Mar 09, 2018 7:08 am
Been thanked: 2 times

Re: Analog volume wheel doesn´t work

Post by SuperPitendo » Wed Jun 27, 2018 5:20 am

Results of ANY test: 0.00

User avatar
kite
Posts: 972
Joined: Thu May 12, 2016 4:30 am
Location: UK
Has thanked: 246 times
Been thanked: 361 times
Contact:

Re: Analog volume wheel doesn´t work

Post by kite » Wed Jun 27, 2018 6:22 am

Right, sounds like 3.3v isn't getting to the connector on the back board.. on the CSO main board itself, that 3pin connector that you are plugging the AVOL 3pin cable in to.. with the CSO on, measure the VOLTAGE from "GND" and "3.3v" on that connector (on the back of it, you should see three silver pins that are soldered on to the PCB)..

You can repeat the same for the same connector on the AVOL board itself.. let me know those results
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/


ImageImageImageImageImage

SuperPitendo
Posts: 13
Joined: Fri Mar 09, 2018 7:08 am
Been thanked: 2 times

Re: Analog volume wheel doesn´t work

Post by SuperPitendo » Wed Jun 27, 2018 6:41 am

Both connectors (CS and Backboard) have 3.3v

User avatar
kite
Posts: 972
Joined: Thu May 12, 2016 4:30 am
Location: UK
Has thanked: 246 times
Been thanked: 361 times
Contact:

Re: Analog volume wheel doesn´t work

Post by kite » Wed Jun 27, 2018 6:50 am

Hm! Ok can you take some pictures up close of the back board, both sides please? Perhaps get soldering iron out and solder from the bottom those pins A B and C with some more fresh solder?
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/


ImageImageImageImageImage

SuperPitendo
Posts: 13
Joined: Fri Mar 09, 2018 7:08 am
Been thanked: 2 times

Re: Analog volume wheel doesn´t work

Post by SuperPitendo » Wed Jun 27, 2018 7:03 am

IMG_2861.JPG
IMG_2861.JPG (183.6 KiB) Viewed 5109 times
IMG_2860.JPG
IMG_2860.JPG (182.29 KiB) Viewed 5109 times

User avatar
kite
Posts: 972
Joined: Thu May 12, 2016 4:30 am
Location: UK
Has thanked: 246 times
Been thanked: 361 times
Contact:

Re: Analog volume wheel doesn´t work

Post by kite » Wed Jun 27, 2018 7:35 am

Right, I think it looks like the back of the 3pin connector on the Back Board isn't soldered properly, it looks to me as if it has been shifted and the pins haven't stuck to the solder.. do you think this is something you can have a go at soldering? It is possible, as these pins are 1mm apart from each other.

If you give it a go, and see if that helps.. if it all goes to pot and is messed up I'll send you a new board out! So there isn't anything to lose! Also it is possible to snip that 3pin cable and solder to those pints A B and C directly, so we've always got that as an option :P
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/


ImageImageImageImageImage

SuperPitendo
Posts: 13
Joined: Fri Mar 09, 2018 7:08 am
Been thanked: 2 times

Re: Analog volume wheel doesn´t work

Post by SuperPitendo » Wed Jun 27, 2018 10:50 am

To be honest... my soldering equipment sucks... it is the cheapest you can find... its good enough to solder 2 soda cans together :lol: but for such tiny things its not adequat :?

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest