sudomod

Helder wrote: ↑

Tue Oct 31, 2017 2:59 am

ecds7393 wrote: ↑

Mon Oct 23, 2017 7:50 pm

Hey guys. I've been watching the AIO sale thread since May. Only seen one or two updates. The last was that the boards were in and would be tested in a week or so... looks like that was months ago. Any idea when there will be more available? Did I missue a new sale thread?

I'm not sure when I'll revisit the AIO again but if you need one RetroGamingNow is selling slightly older versions of my final board I sold, technically the same though.

Chriscox462 wrote: ↑

Sat Nov 04, 2017 1:19 pm

The power coming from the USB hub headers is less than 5v.

RobbsyB wrote: ↑

Tue Nov 07, 2017 2:32 am

Hello everyone,

I am having a problem with my AIO 2.2 board and was hoping to get some support since I am running out of ideas.
The board is connected to a (male) USB plug, so I can connect it to my computer for testing purpose. There are 4 cables that are wired (to male USB plug): GND IN, 5V IN, D- INPUT and D+ INPUT. Speaker and headphone jack are also soldered.

I use the "Game Controllers" tool on my Windows computer to test the AIO board. If I plug it in my computer, a new game controller (named Arduino) shows up in that dialog. I double click that entry to do some button tests (pressing buttons works, as I get feedback from the dialog). However, after a few seconds, the controller will be lost and I get a error message that the controller is no more connected. Eventually, it will show up again in the "Game Controllers" dialog and I can restart the testing. After 2-4 connect/disconnect cycles, I will get a notification (bottom right corner of my screen) that the connected USB device is not recognized (The last connected USB device you connected to this computer malfunctioned...). After this message, I cannot see the controller in the dialog anymore.

Do you have any idea why the AIO board keeps disconnecting?
Thank you for your help!
Cheers!

dryja123 wrote: ↑

Tue Nov 07, 2017 10:03 am

Did you twist your Dat + and Dat - wires?

RobbsyB wrote: ↑

Tue Nov 07, 2017 10:58 am

dryja123 wrote: ↑

Tue Nov 07, 2017 10:03 am

Did you twist your Dat + and Dat - wires?

No. I would not get any connection at all if D+ and D- were switched.

I also soldered a female USB plug to the AIO board and connected a USB mouse to check if it will get disconnected at the same moment the Arduino "Game Controller" looses connection. And yes, it happens in the same moment.

Do you think the FE1.1 USB chip is defective?

Also tested if I get any sound from the speaker. It works. So probably no issues on the audio side...

/opt/retropie/configs/all/runcommand-onstart.sh

#!/bin/sh
# emu name to /dev/shm/runcommand.log
echo "on-start: $2" >&2
if [ "$2" = "pcsx-rearmed" ] || [ "$2" = "mame-mame4all " ] || [ "$2" = "wolf4sdl" ] || [ "$2" = "wolf4sdl-spear" ]
then
sudo killall > /dev/null 2>&1 xboxdrv
sudo /opt/retropie/supplementary/xboxdrv/bin/xboxdrv > /dev/null 2>&1 \
	--evdev /dev/input/by-id/usb-Arduino_LLC_Arduino_Leonardo_HIDAF-if02-event-joystick \
	--silent \
	--detach-kernel-driver \
	--force-feedback \
	--deadzone-trigger 15% \
	--deadzone 4000 \
	--mimic-xpad \
        --device-name "XBOX 360 Controller (xboxdrv)" \
	--evdev-absmap ABS_HAT0X=dpad_x,ABS_HAT0Y=dpad_y \
	--evdev-keymap BTN_TOP=a,BTN_BASE6=b,BTN_PINKIE=x,BTN_BASE2=y,BTN_BASE5=lb,BTN_BASE3=rb,KEY_#300=back,BTN_TOP2=start \
	--dpad-only \
	--ui-axismap lt=void,rt=void \
	--ui-buttonmap tl=void,tr=void,guide=void \
	&
fi

/opt/retropie/configs/all/runcommand-onend.sh

#!/bin/sh
sudo killall > /dev/null 2>&1 xboxdrv

dryja123 wrote: ↑

Tue Nov 07, 2017 11:14 am

No, you must physically twist your dat + and dat - cables, Google "twisted pair cable"
https://en.wikipedia.org/wiki/Twisted_pair