All in One PCB Support Thread

RobbsyB
Posts: 29
Joined: Wed Jan 18, 2017 4:32 am

Re: All in One PCB Support Thread

Post by RobbsyB » Wed May 31, 2017 1:50 pm

Helder wrote:
Wed May 31, 2017 12:54 pm
So if you check for continuity between the 5v In and GND In there's continuity?
Yes! I could not find any solder blobs that might cause this continuity. That's why I suppose that there must be some damaged components on the board.

User avatar
Helder
Trailblazer
Trailblazer
Posts: 2769
Joined: Thu May 05, 2016 8:33 am
Location: Fall River, MA
Has thanked: 1407 times
Been thanked: 3075 times

Re: All in One PCB Support Thread

Post by Helder » Wed May 31, 2017 2:51 pm

Well you can send it back to me and I'll find the part and replace it then send it back to you. Send me a PM so we can trade info.
My Sale Threads:

Retro PSU, 3.5A output!


Chat with me and other members


Don't contact me about obtaining my board files (as you will not get them). Don't contact me about any of my boards if they are sold out, they will be restocked as soon as I can get them.


Don't support thieves like ckliang who copied my AIO to resell and is now cloning the mintyPi, support the original creators and not the thieves!

User avatar
Boydee
Posts: 50
Joined: Fri Apr 14, 2017 1:44 am
Location: Australia
Has thanked: 4 times
Been thanked: 7 times

Re: All in One PCB Support Thread

Post by Boydee » Wed May 31, 2017 9:13 pm

so on that be careful of the multimeter your using, because cheap ones pick up "noise" and may give you a false positive. I had this issue while I was testing for shorts in the data lines with helders latest board. It kept picking up a resistance on the data lines and even the voltage and ground circuits. Just a warning that's all.
Boydees First GBZ : Here

8bitdan
Posts: 17
Joined: Wed Apr 19, 2017 7:04 pm
Has thanked: 1 time

Re: All in One PCB Support Thread

Post by 8bitdan » Mon Jun 05, 2017 5:54 pm

Lololo wrote:
Fri May 05, 2017 5:51 am
me again ;-)

I just do a direct connection with the raspbbery to test the audio but I have two problems:

- with headphone jack I have a lot of noise
- with loudspeaker I have no sound :-(20170505_134132.jpg
Lololo

Where did you get that 3D printed fram pal. and what screen is that you have used in your bult it looks fantastic. any help would be greatly appreciated.

User avatar
HoolyHoo
Posts: 725
Joined: Sat Jul 09, 2016 9:34 pm
Has thanked: 200 times
Been thanked: 720 times

Re: All in One PCB Support Thread

Post by HoolyHoo » Mon Jun 05, 2017 6:15 pm

8bitdan wrote:
Mon Jun 05, 2017 5:54 pm
Lololo wrote:
Fri May 05, 2017 5:51 am
me again ;-)

I just do a direct connection with the raspbbery to test the audio but I have two problems:

- with headphone jack I have a lot of noise
- with loudspeaker I have no sound :-(20170505_134132.jpg
Lololo

Where did you get that 3D printed fram pal. and what screen is that you have used in your bult it looks fantastic. any help would be greatly appreciated.
http://www.sudomod.com/forum/viewtopic.php?f=27&t=2553

Lololo
Posts: 25
Joined: Sat Apr 01, 2017 11:46 am
Has thanked: 24 times
Been thanked: 7 times

Re: All in One PCB Support Thread

Post by Lololo » Tue Jun 06, 2017 2:00 am

8bitdan wrote:
Mon Jun 05, 2017 5:54 pm
Lololo wrote:
Fri May 05, 2017 5:51 am
me again ;-)

I just do a direct connection with the raspbbery to test the audio but I have two problems:

- with headphone jack I have a lot of noise
- with loudspeaker I have no sound :-(20170505_134132.jpg
Lololo

Where did you get that 3D printed fram pal. and what screen is that you have used in your bult it looks fantastic. any help would be greatly appreciated.
Thanks HoolyHoo and the screen is the same as everyone : http://www.gearbest.com/development-boa ... 29447.html

Lololo
Posts: 25
Joined: Sat Apr 01, 2017 11:46 am
Has thanked: 24 times
Been thanked: 7 times

Re: All in One PCB Support Thread

Post by Lololo » Wed Jun 14, 2017 7:01 am

Hello,

I have another question. (sorry :-()
So I decided to put a DAC on my pi3, so I bought a dab sabrent and this amp: https://www.sparkfun.com/products/11044

Do I have to wired the output of the amp to the input PW1 and PW2 of my AIO 2.2a or can I directly wired to ROUT LOUT?

Thank you in advance

User avatar
Helder
Trailblazer
Trailblazer
Posts: 2769
Joined: Thu May 05, 2016 8:33 am
Location: Fall River, MA
Has thanked: 1407 times
Been thanked: 3075 times

Re: All in One PCB Support Thread

Post by Helder » Sat Jun 17, 2017 8:42 am

Just directly to the Rout and Lout
My Sale Threads:

Retro PSU, 3.5A output!


Chat with me and other members


Don't contact me about obtaining my board files (as you will not get them). Don't contact me about any of my boards if they are sold out, they will be restocked as soon as I can get them.


Don't support thieves like ckliang who copied my AIO to resell and is now cloning the mintyPi, support the original creators and not the thieves!

User avatar
Roller Toaster
Posts: 59
Joined: Thu Jun 01, 2017 7:15 pm
Location: McLean, VA
Has thanked: 45 times
Been thanked: 20 times

Re: All in One PCB Support Thread

Post by Roller Toaster » Wed Jul 05, 2017 1:22 am

Not a support question but still about the AIO: what color will the next board be? It's a bit of a shallow question, but I am definitely gonna get one of these next time the orders open up, and use it in an orange pi zero build. I want to use a clear case, and since the screen driver, powerboost, and orange pi are blue, a blue AIO would really complete the look. Obviously I don't expect you to choose a color based on the whim of a single person, but I'm a sucker for consistency and it'd be nice to know how you plan on making it look in the future.

wasonman
Posts: 4
Joined: Wed Aug 24, 2016 7:00 pm

Re: All in One PCB Support Thread

Post by wasonman » Thu Jul 06, 2017 1:46 am

I have all of my build together. I have one tiny problem, the speaker audio is full of interference. How can this be solved?

Thanks Jack

Locked

Who is online

Users browsing this forum: No registered users and 1 guest