3D-Printer Mounted Smoke Detector

Post your Summer 2018 Competition submissions here!
Post Reply
User avatar
Athakaspen
Posts: 9
Joined: Thu Jul 27, 2017 6:10 pm
Has thanked: 10 times
Been thanked: 8 times

3D-Printer Mounted Smoke Detector

Post by Athakaspen » Mon Aug 27, 2018 8:10 pm

IMAG0921.jpg
IMAG0921.jpg (733.07 KiB) Viewed 14963 times
It's finally done! The last parts arrived just over a week before the deadline :shock:

The result is an internet-enabled smoke detector module mounted on the side of my 3D printer. Now, in the event that the mainboard catches fire (not as unlikely on an Anet A8 as it should be), this snazzy box will start beeping incessantly, and I'll get a text message on my phone.
I had planned to wire up a relay so that I could cut the power to the printer too, and I got as far as wiring it to the system on the breadboard with no problems. But, when everything was soldered up, connecting the relay seemed to prevent the ESP32 from starting up at all. The red power light stayed on, but the program never started, and I couldn't connect it to a computer either. Removing the relay made it work perfectly again so I decided to just leave it off. (that's what the stray wire leading from the bottom left of the back of case is for, if anyone was wondering)

This was my first time doing anything with an arduino-type controller, so even though it doesn't do everything I'd wanted it to, I'm not too upset about it. I think I learned a lot (particularly about how bad I am at soldering :lol:), and I had a lot of fun doing it.

Parts:
1. ESP32 - $10.99 from Amazon
2. MQ-2 Smoke Sensor Board - $1.15 from Ebay (price has since increased a few cents)
3. Buzzer Module - $0.76 (USD) from Ebay
4. Relay Board: $0.76 (USD) from Ebay
5. Reset Button - I happened to have one, but here's some similarish ones for $0.79 (USD) on Ebay
6. ~83g of filament @ $23/kg - $1.91
7. Assorted bits of wire, solder, and hot glue - I dunno, $2? We'll go with that.
And that brings the total to just $18.36! I guess that's the advantage of sorting by lowest price on ebay and not caring about shipping times. :P

More photos & demonstration below!
Video DemonstrationShow
More PhotosShow
Back
IMAG0920.jpg
IMAG0920.jpg (451.78 KiB) Viewed 14963 times
Side View
IMAG0923.jpg
IMAG0923.jpg (1.65 MiB) Viewed 14963 times
Underside with Smoke Sensor
IMAG0927.jpg
IMAG0927.jpg (432.79 KiB) Viewed 14963 times
InsideShow
IMAG0930.jpg
IMAG0930.jpg (429.78 KiB) Viewed 14963 times
IMAG0929.jpg
IMAG0929.jpg (413.64 KiB) Viewed 14963 times
Breadboard WiringShow
IMAG0902.jpg
IMAG0902.jpg (784.11 KiB) Viewed 14963 times
3D Model of CaseShow
Enclosure1.PNG
Enclosure1.PNG (165.09 KiB) Viewed 14963 times
Enclosure2.PNG
Enclosure2.PNG (134.42 KiB) Viewed 14963 times
Enclosure3.PNG
Enclosure3.PNG (95.4 KiB) Viewed 14963 times

User avatar
YaYa
Posts: 1719
Joined: Mon Jun 26, 2017 12:42 pm
Location: brittany - France
Has thanked: 871 times
Been thanked: 689 times
Contact:

Re: 3D-Printer Mounted Smoke Detector

Post by YaYa » Wed Aug 29, 2018 3:49 am

Nice project !
Follow me on instagram Image

gamingbro
Posts: 134
Joined: Sat Oct 27, 2018 8:43 am
Has thanked: 7 times
Been thanked: 10 times

Re: 3D-Printer Mounted Smoke Detector

Post by gamingbro » Sat Mar 09, 2019 2:58 pm

coul i fit this inside of a tic tac bin cause that sems like something fun

User avatar
The Cheese Biscuit
Posts: 36
Joined: Wed Aug 15, 2018 4:44 pm
Has thanked: 23 times
Been thanked: 25 times

Re: 3D-Printer Mounted Smoke Detector

Post by The Cheese Biscuit » Mon Mar 11, 2019 3:46 pm

gamingbro wrote:
Sat Mar 09, 2019 2:58 pm
coul i fit this inside of a tic tac bin cause that sems like something fun
...why though?
"I'm not actually a biscuit."

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest