Circuit sword lite segmentation/bus fault/solder bridge

Post Reply
User avatar
JustPlainBill
Posts: 65
Joined: Mon Aug 01, 2016 5:27 pm
Has thanked: 1 time
Been thanked: 32 times

Circuit sword lite segmentation/bus fault/solder bridge

Post by JustPlainBill » Sun Dec 22, 2019 10:46 pm

So I just got my circuit sword lite put together, but when I try to configure the buttons I get a segmentation fault or a bus error, or it just freezes. I pulled everything out of the case and I still get the same errors. I also found a tiny solder bridge on a chip. When I get home I'll try a different sd card. Here's some pictures of the errors, my soldering job, and the solder bridge.

Faults
SpoilerShow
fault 1.jpg
fault 1.jpg (3.22 MiB) Viewed 5525 times
SpoilerShow
fault 2.jpg
fault 2.jpg (618.26 KiB) Viewed 5525 times
SpoilerShow
fault 3.jpg
fault 3.jpg (3.38 MiB) Viewed 5525 times

Soldering pics
SpoilerShow
pi1.jpg
pi1.jpg (540.55 KiB) Viewed 5525 times
SpoilerShow
pi2.jpg
pi2.jpg (588.79 KiB) Viewed 5525 times
SpoilerShow
pi3.jpg
pi3.jpg (1.73 MiB) Viewed 5525 times
SpoilerShow
pi4.jpg
pi4.jpg (1.57 MiB) Viewed 5525 times
SpoilerShow
pi5.jpg
pi5.jpg (503.37 KiB) Viewed 5525 times
SpoilerShow
pi6.jpg
pi6.jpg (466.67 KiB) Viewed 5525 times

Solder Bridge
SpoilerShow
solder bridge.jpg
solder bridge.jpg (241.51 KiB) Viewed 5525 times

User avatar
JustPlainBill
Posts: 65
Joined: Mon Aug 01, 2016 5:27 pm
Has thanked: 1 time
Been thanked: 32 times

Re: Circuit sword lite segmentation/bus fault/solder bridge

Post by JustPlainBill » Thu Dec 26, 2019 7:08 am


User avatar
kite
Posts: 972
Joined: Thu May 12, 2016 4:30 am
Location: UK
Has thanked: 246 times
Been thanked: 361 times
Contact:

Re: Circuit sword lite segmentation/bus fault/solder bridge

Post by kite » Mon Dec 30, 2019 9:36 am

All looks alright, can you get a NEW SD card, or a different one (but a brand new one ideally) and re-burn the image and try that please?
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/


ImageImageImageImageImage

User avatar
JustPlainBill
Posts: 65
Joined: Mon Aug 01, 2016 5:27 pm
Has thanked: 1 time
Been thanked: 32 times

Re: Circuit sword lite segmentation/bus fault/solder bridge

Post by JustPlainBill » Mon Dec 30, 2019 11:57 am

kite wrote:
Mon Dec 30, 2019 9:36 am
All looks alright, can you get a NEW SD card, or a different one (but a brand new one ideally) and re-burn the image and try that please?
Tried a brand new card and still get the same errors.

User avatar
kite
Posts: 972
Joined: Thu May 12, 2016 4:30 am
Location: UK
Has thanked: 246 times
Been thanked: 361 times
Contact:

Re: Circuit sword lite segmentation/bus fault/solder bridge

Post by kite » Tue Dec 31, 2019 4:32 am

hm, did the pi work before you hooked it all up?

And to confirm, this is using the LITE image right? https://github.com/kiteretro/Circuit-Sw ... e/releases

What might be worth doing is getting the stock image, and then copying the 'config.txt' from the CSLite image onto the stock image, this will allow the internal screen to work. Not much else will (sound, input, menu, etc) however if it boots all the way up, then that's a good sign!
Stock clearance - CLOSED: viewtopic.php?f=38&t=12064
Kite's Mailing List: https://goo.gl/forms/e97uUvPOfUxPWdz82
Kite's FAQ: https://kiteretro.com/faq/


ImageImageImageImageImage

User avatar
JustPlainBill
Posts: 65
Joined: Mon Aug 01, 2016 5:27 pm
Has thanked: 1 time
Been thanked: 32 times

Re: Circuit sword lite segmentation/bus fault/solder bridge

Post by JustPlainBill » Tue Dec 31, 2019 11:59 am

kite wrote:
Tue Dec 31, 2019 4:32 am
hm, did the pi work before you hooked it all up?

And to confirm, this is using the LITE image right? https://github.com/kiteretro/Circuit-Sw ... e/releases

What might be worth doing is getting the stock image, and then copying the 'config.txt' from the CSLite image onto the stock image, this will allow the internal screen to work. Not much else will (sound, input, menu, etc) however if it boots all the way up, then that's a good sign!
I didn't test the pi, it was brand new and I didn't even think about it, oops. Yes I'm using the lite version, Circuit-Sword-Lite-Software-v1.0.1.zip

I'll try the stock image when I get to work and see what happens. Thanks.

User avatar
JustPlainBill
Posts: 65
Joined: Mon Aug 01, 2016 5:27 pm
Has thanked: 1 time
Been thanked: 32 times

Re: Circuit sword lite segmentation/bus fault/solder bridge

Post by JustPlainBill » Wed Jan 01, 2020 4:21 am

It's still the same. It boots up fine and starts emulation station and then asks to configure a controller. Once I start pushing the buttons I get the error. I also plugged in a usb controller and the same thing happens when I try to configure that.

DouglasLix
Posts: 3
Joined: Thu Jan 30, 2020 3:34 pm

Circuit sword lite segmentation/bus fault/solder bridge

Post by DouglasLix » Sun Feb 02, 2020 5:48 am

I have just installed Fedora 64 and fully updated it. After that, I installed EB1 and when I run ./eschalon_book_1 it gives me the following error:
./eschalon_book_1
Setting sound driver: Default
Segmentation fault core dumped

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest