[PREORDER] Game Boy Cart Micro SD Card Boards
-
- Posts: 279
- Joined: Fri May 06, 2016 5:36 pm
- Has thanked: 16 times
- Been thanked: 229 times
[PREORDER] Game Boy Cart Micro SD Card Boards
I have designed a PCB to replace the original PCB in the Game Boy Cart. This board has a micro SD card slot on it and will interface with the original game boy Card edge connector. These boards will come assembled with the micro SD card slot and some decoupling caps for the power. For this board the fingers will need to be plated with the thick gold to handle repeated insertion and removals. Immersion gold or silver solder will wear down very quickly. This thick gold adds to the cost of the PCB. I am Pre-selling these boards to make sure there is enough interest due to the higher cost of the PCBs. The Pre-orders will get free shipping. fully assembled boards will be $22. I will open pre-order to 20 people and will order the boards once we reach at least 5. Once ordered It will take about 10 days to get the boards in house. If anyone in the EU or UK would like to sell these PM me and we can arrange a bulk sale. I will provide a guide telling customers exactly which pins on the card edge to solder to exactly which test points on the Pi Zero.
I will post a screen shot of the PCB in the layout software tomorrow when I get to work. I am an electronics engineer for a large chip maker and do layout as part of my job.
Please reply to this post when you place your order and shoot me a PM confirming your paypal email account.
I have decided to order even if I only get 5.
Thanks
PreRunnerSeth _ PRS-TECH
1. jlane52641
2. ktechelonbreak
3. hoot
4. mgsickler
5. DirtyBeagles
6. choochootrain23
7. choochootrain23
8. 129jbc
9. Cannikin
10. Alexkidd2
11. SidSilver
12.petran1420
13.petran1420
14. Revojames
15. Rod2D2
16. Jlane52641
17. loafslice
18. topher
19. Tindalos
20. unknown buyer
I will post a screen shot of the PCB in the layout software tomorrow when I get to work. I am an electronics engineer for a large chip maker and do layout as part of my job.
Please reply to this post when you place your order and shoot me a PM confirming your paypal email account.
I have decided to order even if I only get 5.
Thanks
PreRunnerSeth _ PRS-TECH
1. jlane52641
2. ktechelonbreak
3. hoot
4. mgsickler
5. DirtyBeagles
6. choochootrain23
7. choochootrain23
8. 129jbc
9. Cannikin
10. Alexkidd2
11. SidSilver
12.petran1420
13.petran1420
14. Revojames
15. Rod2D2
16. Jlane52641
17. loafslice
18. topher
19. Tindalos
20. unknown buyer
Last edited by prerunnerseth on Sat May 28, 2016 5:57 pm, edited 23 times in total.
- jlane52641
- Posts: 53
- Joined: Fri May 06, 2016 4:00 am
- Location: Southeast Iowa
- Has thanked: 18 times
- Been thanked: 5 times
-
- Posts: 78
- Joined: Wed May 04, 2016 10:07 pm
- Been thanked: 7 times
Re: (PREORDER) Game Boy Cart Micro SD Card Boards
In for one as well! I'm looking to make a 2nd GBZ and this seems like a very easy way to avoid all that wiring. Quick question, is this just for the top half or does this PCB cover the entire Gameboy (button PCB) ?
-
- Posts: 279
- Joined: Fri May 06, 2016 5:36 pm
- Has thanked: 16 times
- Been thanked: 229 times
Re: (PREORDER) Game Boy Cart Micro SD Card Boards
This is just for the board that goes into a game boy cartridge and interfaces with the original game boy connector. It has the micro SD card socket on it.ktechelonbreak wrote:In for one as well! I'm looking to make a 2nd GBZ and this seems like a very easy way to avoid all that wiring. Quick question, is this just for the top half or does this PCB cover the entire Gameboy (button PCB) ?
- Rod2D2
- Posts: 131
- Joined: Thu May 05, 2016 5:08 am
- Location: USA
- Has thanked: 80 times
- Been thanked: 17 times
Re: (PREORDER) Game Boy Cart Micro SD Card Boards
prerunnerseth wrote:I have designed a PCB to replace the original PCB in the Game Boy Cart. This board has a micro SD card slot on it and will interface with the original game boy Card edge connector. These boards will come assembled with the micro SD card slot and some decoupling caps for the power. For this board the fingers will need to be plated with the thick gold to handle repeated insertion and removals. Immersion gold or silver solder will wear down very quickly. This thick gold adds to the cost of the PCB. I am Pre-selling these boards to make sure there is enough interest due to the higher cost of the PCBs. The Pre-orders will get free shipping. fully assembled boards will be $22. I will open pre-order to 20 people and will order the boards once we reach at least 10. Once ordered It will take about 10 days to get the boards in house. If anyone in the EU or UK would like to sell these PM me and we can arrange a bulk sale. I will provide a guide telling customers exactly which pins on the card edge to solder to exactly which test points on the Pi Zero.
I will post a screen shot of the PCB in the layout software tomorrow when I get to work. I am an electronics engineer for a large chip maker and do layout as part of my job.
Please reply to this post when you place your order and shoot me a PM confirming your paypal email account.
If we don't reach 10 I will refund all payments received.
Thanks
PreRunnerSeth _ PRS-TECH
1. jlane52641
2. ktechelonbreak
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
So will something still need to be soldered to the Pi zero from the cartridge? What will need to be done to make it work with the original cartridge reader? Also are you selling in the USA ?
Last edited by Rod2D2 on Thu Jun 09, 2016 7:00 am, edited 1 time in total.
-
- Posts: 279
- Joined: Fri May 06, 2016 5:36 pm
- Has thanked: 16 times
- Been thanked: 229 times
Re: (PREORDER) Game Boy Cart Micro SD Card Boards
Not sure you mean to make it compatible with the original cardridge. You will mount this board into a cartridge. Modifly it a little to allow you to insert and remove the micro SD card. Inside the gameboy you will solder a few pins on the original card edge connector to your pi zero. Then mount the card edge connector in the case and you're good to go. Works much like the original project except you won't have to cut up a cartridge PCB and solder in the micro SD card adapter.
I am located in the US.
I am located in the US.
Re: (PREORDER) Game Boy Cart Micro SD Card Boards
Since i already have the kk_gb_brkout from kitsch-bent i suppose all this thing does is save me the trouble of soldering the sd card adapter to the brkout? If i didn't already buy and have that i would probably have bought this. :/ I should learn how to solder anyway though.
- 1461748123
- Posts: 143
- Joined: Wed May 04, 2016 8:36 pm
- Has thanked: 9 times
- Been thanked: 17 times
-
- Posts: 279
- Joined: Fri May 06, 2016 5:36 pm
- Has thanked: 16 times
- Been thanked: 229 times
Re: (PREORDER) Game Boy Cart Micro SD Card Boards
The thick gold adds significantly and the Micro SD card slots are $3 a piece.1461748123 wrote:I will say the price is ridiculously high :/
Here are images of the PCB in layout software and one of a cutout with a socket laying on top in the cart case.
-
- Posts: 279
- Joined: Fri May 06, 2016 5:36 pm
- Has thanked: 16 times
- Been thanked: 229 times
Re: [PREORDER] Game Boy Cart Micro SD Card Boards
Hope this clears up some confusion. This replaces what you see below with a custom PCB with the card slot already mounted on it. The reason for the cost is the gold fingers that make repeated contact with the connector in the game boy need to have whats called thick gold plating. the immersion gold or silver solder will wear down very quickly. The price for the card slot is also $3 a piece.
Who is online
Users browsing this forum: No registered users and 1 guest