Ant's Circuit Sword STL Files (joystick, shoulder button, exhaust fan cartridge)

Share your STL files, CAD design files, etc. here!
User avatar
AntFJ
Posts: 132
Joined: Thu Nov 16, 2017 8:09 pm
Has thanked: 27 times
Been thanked: 92 times

Ant's Circuit Sword STL Files (joystick, shoulder button, exhaust fan cartridge)

Post by AntFJ » Sun Mar 04, 2018 5:41 pm

Hi all, my first attempt at making a thread here on sudomod. I've made some .stl files that I think will be helpful to other folks out there.

First is a joystick in the bottom left of the case. You will still need to epoxy it down. The screws are from Amazon M1.8x5mm https://www.amazon.com/gp/product/B01FK ... UTF8&psc=1. You will need to clip off a couple of mm to make them short enough so they don't push into the case when you screw the joystick in. The gameboy case is so thick you may need to add a piece of paper in the joystick cap to make it extend a little longer. Ensure the bracket is glued as close as possible to the case so that the joystick is as low as possible when mounted. Solder your wires from the right and wrap them around and up the hole through kites board - if kites board presses too hard on the back of the joystick it can make it not return to center - don't forget your kapton tape! I designed my own center joystick holder and modeled it off of @HoolyHoo 's Screen Bracket w/joystick. Since my design is basically the same as his I won't be posting that here.
PSP Joystick Lower GBZ Bracket KAIO Circuit Sword.stl
(157.31 KiB) Downloaded 209 times
20180227_211538.jpg
20180227_211538.jpg (876.54 KiB) Viewed 7835 times
20180227_211547.jpg
20180227_211547.jpg (834.82 KiB) Viewed 7835 times
20180227_211903.jpg
20180227_211903.jpg (1.69 MiB) Viewed 7835 times
20180304_133257.jpg
20180304_133257.jpg (918.99 KiB) Viewed 7835 times

Second is my back button design. I really like how the the start/select buttons feel and look so I made these files. This works with Kite's back button board. The drill guide is for a 2mm drill and the final drill diameter is a 3mm drill.
Start Select Shoulder Guide.stl
(135.53 KiB) Downloaded 297 times
Start & Select Back Button Bottom.stl
(632.11 KiB) Downloaded 148 times
Start & Select Back Button Top.stl
(98.03 KiB) Downloaded 174 times
20180225_221322.jpg
20180225_221322.jpg (1006.06 KiB) Viewed 7835 times
20180227_223354.jpg
20180227_223354.jpg (939.29 KiB) Viewed 7835 times
20180304_133307.jpg
20180304_133307.jpg (1.07 MiB) Viewed 7835 times
Last edited by AntFJ on Sun Apr 21, 2019 4:46 pm, edited 6 times in total.

User avatar
AntFJ
Posts: 132
Joined: Thu Nov 16, 2017 8:09 pm
Has thanked: 27 times
Been thanked: 92 times

Re: Kite's Circuit Sword Fan Mount, Joystick, and Back Buttons

Post by AntFJ » Sun Mar 04, 2018 5:46 pm

Here are some more back buttons... it uses the standard DMG buttons/pad
Two button Top.stl
(96.47 KiB) Downloaded 331 times
Two button bottom.stl
(149.5 KiB) Downloaded 331 times
20180225_221351.jpg
20180225_221351.jpg (987.31 KiB) Viewed 7834 times
Finally, here is the fan bracket I used. It mounts the fan into the cartridge and forces the hot air out of the case. I hot glued a JST plug next to the fan so that the back of the case can still be completely removed. You must use a low profile heatsink. The one provided by kite works great.

I've added a blank and CM3 version.
Cart With Fan Vent.stl
(499.98 KiB) Downloaded 316 times
CM3 Cart with Fan Vent.stl
(586.12 KiB) Downloaded 173 times
Blank Cart With Fan Vent.stl
(176.84 KiB) Downloaded 167 times
20180304_133329.jpg
20180304_133329.jpg (1.08 MiB) Viewed 7834 times
20180304_110029.jpg
20180304_110029.jpg (1.26 MiB) Viewed 7834 times
20181017_082552.jpg
20181017_082552.jpg (289.04 KiB) Viewed 3987 times
Last edited by AntFJ on Wed Oct 17, 2018 9:38 am, edited 2 times in total.

User avatar
AntFJ
Posts: 132
Joined: Thu Nov 16, 2017 8:09 pm
Has thanked: 27 times
Been thanked: 92 times

Re: Kite's Circuit Sword Fan Mount, Joystick, and Back Buttons

Post by AntFJ » Sun Mar 04, 2018 5:47 pm

Also I forgot to include the joystick drill guide. If I remember correctly the PSP joysticks are 10mm... make sure to measure yours though - I don't remember off the top of my head.
PSP Joystick Guide.stl
(54.57 KiB) Downloaded 349 times
Last edited by AntFJ on Sun Mar 11, 2018 9:16 pm, edited 1 time in total.

Double0EK
Posts: 70
Joined: Thu Dec 08, 2016 4:50 pm
Has thanked: 51 times
Been thanked: 8 times

Re: Kite's Circuit Sword Fan Mount, Joystick, and Back Buttons

Post by Double0EK » Sun Mar 04, 2018 11:11 pm

Wow! Really like the use of the Start/Select Buttons for shoulder buttons!

zerogeek
Posts: 9
Joined: Mon Aug 01, 2016 8:55 am
Has thanked: 3 times
Been thanked: 4 times

Re: Kite's Circuit Sword Fan Mount, Joystick, and Back Buttons

Post by zerogeek » Mon Mar 05, 2018 6:32 pm

I love these brackets. This may be obvious to others, but there were a couple things that had me stumped. Let me preface this with the fact that I haven't wired this up yet, but I DID check with a multi-meter. I had been planning on using only L1/R1. If you use all four, the bracket sits backwards in the case (Left is Right and Right is Left). Will this matter? I doubt it as you are telling Retropie what button you want to use for everything, heck... you could use Start for L1 if you wanted.... but my OCD is going CRAZY!

Second, I already had my HDMI board set up with the 2 risers soldered in. You will need to remove those if you use this bracket because AntFJ was awesome and made a bracket that does EVERYTHING!

Thanks again for this design and sharing your STL files. I will finally have all four back buttons :)

Sasherz
Posts: 77
Joined: Wed Jul 26, 2017 2:50 pm
Location: Norway
Has thanked: 6 times
Been thanked: 5 times

Re: Kite's Circuit Sword Fan Mount, Joystick, and Back Buttons

Post by Sasherz » Tue Mar 06, 2018 12:22 pm

what would the dammage be if I asked for two set to be made?
would need the main mount and the mount for the second thumbstick
would need them in black, due to a two tone theme.
allso the game cartridge does look interesting, should be in classic grey
but for the back, Im going with four tacktile buttons layout thats on the other side of the kite's backboard.

so:
2x main bracket for psp stick (black)
2x bracket for 2nd psp stick (black)
2x gamecartridge with the fan holes in the natural grey

User avatar
AntFJ
Posts: 132
Joined: Thu Nov 16, 2017 8:09 pm
Has thanked: 27 times
Been thanked: 92 times

Re: Kite's Circuit Sword Fan Mount, Joystick, and Back Buttons

Post by AntFJ » Tue Mar 06, 2018 9:12 pm

Someone PM'd me for the center screen/center bracket. As I mentioned before that screen bracket is based off Hoolyhoo's design so I won't give that .stl file away. I will give the part that I designed though. It can be added to any screen bracket if you know how to manipulate .stl files.

Here is an image showing how it lines up.
combine.PNG
combine.PNG (61.99 KiB) Viewed 7678 times
PSP Joystick Upper GBZ Bracket flush attempt 2.stl
(65.22 KiB) Downloaded 319 times

User avatar
AntFJ
Posts: 132
Joined: Thu Nov 16, 2017 8:09 pm
Has thanked: 27 times
Been thanked: 92 times

Re: Kite's Circuit Sword Fan Mount, Joystick, and Back Buttons

Post by AntFJ » Tue Mar 06, 2018 9:26 pm

I have no problem making you the 2nd joysticks and the cartridge. I can't make the screen bracket for you - it isn't my design. You'll have to go to Hoolyhoo's for sale thread to get it from him.

I foresee a few issues... I don't have black or grey filament and shipping to Norway (from the US) may be cost prohibitive. Is there no local 3d printing service you can use? If you absolutely must have me make these I'll need to buy the filament and figure out how much shipping will cost.
Last edited by AntFJ on Sun Mar 11, 2018 9:17 pm, edited 1 time in total.

Sasherz
Posts: 77
Joined: Wed Jul 26, 2017 2:50 pm
Location: Norway
Has thanked: 6 times
Been thanked: 5 times

Re: Kite's Circuit Sword Fan Mount, Joystick, and Back Buttons

Post by Sasherz » Fri Mar 09, 2018 1:35 pm

how much would it cost for:
2x bracket for 2nd psp stick (need to be black)
2x gamecartridge with the fan holes, (one orange and one in black)
with shipping to Norway?
I dont have a 3D printer and people over here want 100 bucks for the printing and another 20 for shipping with normal mail :/ (greedy bastards)

User avatar
YaYa
Posts: 1719
Joined: Mon Jun 26, 2017 12:42 pm
Location: brittany - France
Has thanked: 871 times
Been thanked: 688 times
Contact:

Re: Kite's Circuit Sword Fan Mount, Joystick, and Back Buttons

Post by YaYa » Sat Mar 17, 2018 1:11 am

Awesome job ! bravo :D
Follow me on instagram Image

Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests