V3 screen issues. How to fix them!
- LilTrublMakr
- Posts: 365
- Joined: Sun Aug 05, 2018 6:39 am
- Has thanked: 24 times
- Been thanked: 120 times
- Contact:
V3 screen issues. How to fix them!
Just doing a little write up of the v3 screen issues.
Cause: The PCB maker that Helder used didn't set up their machines correctly and the ribbon cable of the screen is not making full contact with the pads on the screen PCB. This is causing dark spots on the bottom of the screen and possibly even the screen not working at all.
Fix: It is actually pretty easy to fix this issue, All you need to do is very carefully separate the screen from the board while leaving the ribbon cable attached, and reflow the ribbon with flux. It would be easiest to get a flux pen if you do not have one already. Just add a little bit of flux and run your tip over each of the ribbon connections.
This may take a few tries to get working properly. If using just flux isn't working, try adding a little bit of new solder to the pins.
Helder made a video on his Instagram about the issue and how to fix it. It can be viewed here: https://www.instagram.com/p/Bu4pEUrF3C5/
Cause: The PCB maker that Helder used didn't set up their machines correctly and the ribbon cable of the screen is not making full contact with the pads on the screen PCB. This is causing dark spots on the bottom of the screen and possibly even the screen not working at all.
Fix: It is actually pretty easy to fix this issue, All you need to do is very carefully separate the screen from the board while leaving the ribbon cable attached, and reflow the ribbon with flux. It would be easiest to get a flux pen if you do not have one already. Just add a little bit of flux and run your tip over each of the ribbon connections.
This may take a few tries to get working properly. If using just flux isn't working, try adding a little bit of new solder to the pins.
Helder made a video on his Instagram about the issue and how to fix it. It can be viewed here: https://www.instagram.com/p/Bu4pEUrF3C5/
@LilTrublMakr
My website
My shop
My MintyPi Services
wpa_supplicant generator
Sudomod Wiki Links:
-mintyPi FaQ
-mintyPi V3: parts, tools needed, build guide, and software
-mintyPi V3: How to connect to WiFi and transfer ROMs. A step by step picture guide!
My projects:
Circuit Sword CM3 Build
My website
My shop
My MintyPi Services
wpa_supplicant generator
Sudomod Wiki Links:
-mintyPi FaQ
-mintyPi V3: parts, tools needed, build guide, and software
-mintyPi V3: How to connect to WiFi and transfer ROMs. A step by step picture guide!
My projects:
Circuit Sword CM3 Build
- Helder
- Trailblazer
- Posts: 2985
- Joined: Thu May 05, 2016 8:33 am
- Location: Rogers, AR
- Has thanked: 1459 times
- Been thanked: 3114 times
Re: V3 screen issues. How to fix them!
Nice repost, I'm going to post here a bunch things people are having issues with. First and foremost soldering problems between the PI and controller pcb are 75% of all problems.
People always assume the soldering is perfect but a few threads down the issue was bad solder joint. I fixed a setup recently (yesterday) for a customer who had no audio or power from the battery.
The problem? Bad solder joint on the 5v GPIO which powers audio and the whole pi off of battery power. And the PI soldering "looked" good but doing s continuity test said otherwise.
People always assume the soldering is perfect but a few threads down the issue was bad solder joint. I fixed a setup recently (yesterday) for a customer who had no audio or power from the battery.
The problem? Bad solder joint on the 5v GPIO which powers audio and the whole pi off of battery power. And the PI soldering "looked" good but doing s continuity test said otherwise.
Chat with me and other members On Discord
Don't contact me about obtaining my board files (as you will not get them). If my Boards or PCB Kits are sold out, they will be restocked as soon as I can get them and there is demand for them. You can join the mailing list on my Website to be notified when they are available.
Helder's Game Tech Website
We will not support any cloned work so don't come to us with technical issues to resolve, go talk to the cloner for help.
Don't contact me about obtaining my board files (as you will not get them). If my Boards or PCB Kits are sold out, they will be restocked as soon as I can get them and there is demand for them. You can join the mailing list on my Website to be notified when they are available.
Helder's Game Tech Website
We will not support any cloned work so don't come to us with technical issues to resolve, go talk to the cloner for help.
- DieselDummy
- Posts: 197
- Joined: Tue Oct 24, 2017 12:20 pm
- Location: Florida, USA
- Has thanked: 80 times
- Been thanked: 92 times
Re: V3 screen issues. How to fix them!
The continuity test is huge! That cannot be stressed enough. My pi was soldered to the board perfectly in my opinion, but the continuity test proved otherwise. Always do the continuity test!
Links
"Battery Cover Buttons" install guide and support
My CSO build #1 - with "Battery Cover Buttons"
My CSO build #2 - the "sudoNod"
My MintyPi v3 build #1
"If you're bored, you're boring."
"Battery Cover Buttons" install guide and support
My CSO build #1 - with "Battery Cover Buttons"
My CSO build #2 - the "sudoNod"
My MintyPi v3 build #1
"If you're bored, you're boring."
Re: V3 screen issues. How to fix them!
Well I started with a black screen. First reflow(and some double checking my continuity) and I got a screen with a large dark section. Second reflow with a bit of solder and I’m down to a small black area towards the bottom. So I figure one more reflow and I’ll have it.
Thanks for all the help. I’ve done other DYI electronic projects like this and the creators have not been that helpful. I appreciate you letting people know about issues and give us practical fixes.
Edit: After several more reflow attempts I got it to be just a small black spot at the bottom. I am ready to give up on it honestly. It's only noticeable when the screen is complete white and I don't see it being a problem when games run on it. I may give it one more try after I get the tin all setup.
Just a thought for you guys. It may be worth a short Youtube video alerting people of the issue and the fix. No everyone uses Instagram and it may be a better way to help get the word out.
Thanks for all the help. I’ve done other DYI electronic projects like this and the creators have not been that helpful. I appreciate you letting people know about issues and give us practical fixes.
Edit: After several more reflow attempts I got it to be just a small black spot at the bottom. I am ready to give up on it honestly. It's only noticeable when the screen is complete white and I don't see it being a problem when games run on it. I may give it one more try after I get the tin all setup.
Just a thought for you guys. It may be worth a short Youtube video alerting people of the issue and the fix. No everyone uses Instagram and it may be a better way to help get the word out.
Re: V3 screen issues. How to fix them!
I have the same problem, is there any way the send mine back and order a new one?
- LilTrublMakr
- Posts: 365
- Joined: Sun Aug 05, 2018 6:39 am
- Has thanked: 24 times
- Been thanked: 120 times
- Contact:
Re: V3 screen issues. How to fix them!
You can send it back to Helder or myself.
I am helping repair the parts that have been messed up by the PCB fab since Helder is getting all of the issues fixed before sending out more kits and also repairing parts on top of his normal life. Just trying to relieve the strain on him a little bit. I am sure Helder will say that it is ok to send stuff to me if someone asks.
So if you do have me repair the boards, I will need the whole kit (with the pi soldered on) so I can test everything and make sure it all works since I don't have a kit available to test with. I have the chips on order and they are on their way from China. They should be in in a week or two for me to replace the dualfet.
Ultimately, the option is yours.
I am helping repair the parts that have been messed up by the PCB fab since Helder is getting all of the issues fixed before sending out more kits and also repairing parts on top of his normal life. Just trying to relieve the strain on him a little bit. I am sure Helder will say that it is ok to send stuff to me if someone asks.
So if you do have me repair the boards, I will need the whole kit (with the pi soldered on) so I can test everything and make sure it all works since I don't have a kit available to test with. I have the chips on order and they are on their way from China. They should be in in a week or two for me to replace the dualfet.
Ultimately, the option is yours.
@LilTrublMakr
My website
My shop
My MintyPi Services
wpa_supplicant generator
Sudomod Wiki Links:
-mintyPi FaQ
-mintyPi V3: parts, tools needed, build guide, and software
-mintyPi V3: How to connect to WiFi and transfer ROMs. A step by step picture guide!
My projects:
Circuit Sword CM3 Build
My website
My shop
My MintyPi Services
wpa_supplicant generator
Sudomod Wiki Links:
-mintyPi FaQ
-mintyPi V3: parts, tools needed, build guide, and software
-mintyPi V3: How to connect to WiFi and transfer ROMs. A step by step picture guide!
My projects:
Circuit Sword CM3 Build
Re: V3 screen issues. How to fix them!
mainly i wanted to send the screen back so ether i could use it or someone else could insted of me just ordering a new screen and haveing a falty extra, is there a way to just order a new screen with nothing else?? my parents won't let me send it to someone i dont know anything diffinitive aboutLilTrublMakr wrote: ↑Sun Mar 31, 2019 4:00 pmYou can send it back to Helder or myself.
I am helping repair the parts that have been messed up by the PCB fab since Helder is getting all of the issues fixed before sending out more kits and also repairing parts on top of his normal life. Just trying to relieve the strain on him a little bit. I am sure Helder will say that it is ok to send stuff to me if someone asks.
So if you do have me repair the boards, I will need the whole kit (with the pi soldered on) so I can test everything and make sure it all works since I don't have a kit available to test with. I have the chips on order and they are on their way from China. They should be in in a week or two for me to replace the dualfet.
Ultimately, the option is yours.
- LilTrublMakr
- Posts: 365
- Joined: Sun Aug 05, 2018 6:39 am
- Has thanked: 24 times
- Been thanked: 120 times
- Contact:
Re: V3 screen issues. How to fix them!
Understandable. You could try fixing it yourself though. If you have flux, it would make it a lot easier. I have a better explanation on how to fix it in the other post.
Really, you would have to do this process anyways to replace the screen so it won't hurt to try it before ordering a new screen. Unless I am misunderstanding and you have tried to do this and broke the screen?LilTrublMakr wrote: ↑Wed Mar 27, 2019 7:42 pmScreen Issues:
Instagram Posts: Post 1, Post 2.
If your screen is not showing anything, showing up white, or has dark spots on the screen, you need to reflow the ribbon cable.
Cause: The PCB maker that Helder used didn't set up their machines correctly and the ribbon cable of the screen is not making full contact with the pads on the screen PCB. This is causing dark spots on the bottom of the screen and possibly even the screen not working at all.
Fix: It is actually pretty easy to fix this issue, All you need to do is very carefully separate the screen from the board while leaving the ribbon cable attached, and reflow the ribbon with flux. It would be easiest to get a flux pen if you do not have one already. Just add a little bit of flux and run your tip over each of the ribbon connections.
My recommendations are as follows:
1. Use something thin like a guitar pick to separate the screen from the PCB. TAKE YOUR TIME! Use the pick on the 3 sides that does not have the ribbon.
2. Use lots of flux. Flux is your friend.
3. Put some fresh solder on the tip of your iron every couple of pins. You don't need much.
4. Work from the pad of the PCB and SLOWLY work your way up to the pin of the ribbon cable.
5. TAKE YOUR TIME!
If you need a video tutorial, there is one on the 3rd slide of this Instagram post.
If you do not feel comfortable fixing any of these issues, get in touch with Helder or myself and send the parts to one of us and we will fix the problem(s).
@LilTrublMakr
My website
My shop
My MintyPi Services
wpa_supplicant generator
Sudomod Wiki Links:
-mintyPi FaQ
-mintyPi V3: parts, tools needed, build guide, and software
-mintyPi V3: How to connect to WiFi and transfer ROMs. A step by step picture guide!
My projects:
Circuit Sword CM3 Build
My website
My shop
My MintyPi Services
wpa_supplicant generator
Sudomod Wiki Links:
-mintyPi FaQ
-mintyPi V3: parts, tools needed, build guide, and software
-mintyPi V3: How to connect to WiFi and transfer ROMs. A step by step picture guide!
My projects:
Circuit Sword CM3 Build
- Helder
- Trailblazer
- Posts: 2985
- Joined: Thu May 05, 2016 8:33 am
- Location: Rogers, AR
- Has thanked: 1459 times
- Been thanked: 3114 times
Re: V3 screen issues. How to fix them!
Send it back to me in a box or something protective not an envelope so the LCD is not damaged and I'll fix it. If the LCD arrives damaged as in cracked or you damaged it in an attempt to fix it then I will not give you a freebie you will have to pay for a new LCD.majora wrote: ↑Sun Mar 31, 2019 8:20 pmmainly i wanted to send the screen back so ether i could use it or someone else could insted of me just ordering a new screen and haveing a falty extra, is there a way to just order a new screen with nothing else?? my parents won't let me send it to someone i dont know anything diffinitive about
Chat with me and other members On Discord
Don't contact me about obtaining my board files (as you will not get them). If my Boards or PCB Kits are sold out, they will be restocked as soon as I can get them and there is demand for them. You can join the mailing list on my Website to be notified when they are available.
Helder's Game Tech Website
We will not support any cloned work so don't come to us with technical issues to resolve, go talk to the cloner for help.
Don't contact me about obtaining my board files (as you will not get them). If my Boards or PCB Kits are sold out, they will be restocked as soon as I can get them and there is demand for them. You can join the mailing list on my Website to be notified when they are available.
Helder's Game Tech Website
We will not support any cloned work so don't come to us with technical issues to resolve, go talk to the cloner for help.
Re: V3 screen issues. How to fix them!
Ok, what address should i send it to? and i haven't messed with it at allHelder wrote: ↑Mon Apr 01, 2019 6:26 amSend it back to me in a box or something protective not an envelope so the LCD is not damaged and I'll fix it. If the LCD arrives damaged as in cracked or you damaged it in an attempt to fix it then I will not give you a freebie you will have to pay for a new LCD.majora wrote: ↑Sun Mar 31, 2019 8:20 pmmainly i wanted to send the screen back so ether i could use it or someone else could insted of me just ordering a new screen and haveing a falty extra, is there a way to just order a new screen with nothing else?? my parents won't let me send it to someone i dont know anything diffinitive about
Who is online
Users browsing this forum: No registered users and 1 guest